1000+ Hydraulics & Fluid Machineries MCQ for GATE [Solved]

1. Specific speed for reaction turbines ranges from
A. 0 to 4.5
B. 10 to 100
C. 80 to 200
D. 250 to 300
Answer : B

2. If the net positive suction head (NPSH) requirement for the pump is not satisfied, then
A. No flow will take place
B. Cavitation will be formed
C. Efficiency will be low
D. Excessive power will be consumed
Answer : B

3. The force exerted by a jet of water impinging normally on a plate which due to the impact of jet, moves in the direction of jet with a velocity v is
A. [wa (V - v)]/2g
B. [wa (V - v)]/g
C. [wa (V - v)²]/2g
D. [wa (V - v²)]/g
Answer : D

4. The ratio of the normal force of jet of water on a plate inclined at an angle of 30° as compared to that when the plate is normal to jet, is
A. 1/?2
B. 1/2
C. 1
D. ?2
Answer : B

5. Reciprocating pumps are no more to be seen in industrial applications (in comparison to centrifugal pumps) because of
A. High initial and maintenance cost
B. Lower discharge
C. Lower speed of operation
D. Necessity of air vessel
Answer : A

6. In centrifugal pumps, maximum efficiency is obtained when the blades are
A. Straight
B. Bent forward
C. Bent backward
D. Radial
Answer : C

7. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit discharge of wheel is
A. 0.25 m³/s
B. 0.5 m³/s
C. 1.5 m³/s
D. 2.5 m³/s
Answer : A

8. In impulse Turbine, energy available at the inlet is in the form of
A. Potential Energy
B. Strain Energy
C. Kinetic energy
D. None of these
Answer : C

9. Motion of a liquid in a volute casing of a centrifugal pump is an example of
A. Rotational flow
B. Radial
C. Forced spiral vortex flow
D. Spiral vortex flow
Answer : D

10. The number of buckets on the periphery of a Pelton wheel is given by
A. (D/2d) + 5
B. (D/2d) + 10
C. (D/2d) + 15
D. (D/2d) + 20
Answer : C

11. A hydraulic press is a device used
A. To store pressure energy which may be supplied to a machine later on
B. To increase the intensity of pressure of water by means of energy available from a large quantity of water at a low pressure
C. To lift larger load by the application of a comparatively much smaller force
D. All of the above
Answer : C

12. A hydraulic coupling belongs to the category of
A. Power absorbing machines
B. Power developing machines
C. Energy transfer machines
D. Energy generating machines
Answer : C

13. Which of the following turbine is preferred for a specific speed of 60 to 300 r.p.m.?
A. Pelton wheel
B. Francis turbine
C. Kaplan turbine
D. None of these
Answer : B

14. In a Kaplan turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : B

15. Air vessels in reciprocating pump are used to
A. Smoothen flow
B. Reduce acceleration to minimum
C. Increase pump efficiency
D. Save pump from cavitations
Answer : B

16. The specific speed (Ns) of a centrifugal pump is given by
A. (N?Q)/H^2/3
B. (N?Q)/H^3/4
C. (N?Q)/H
D. (N?Q)/H^5/4
Answer : B

17. The efficiency of jet propulsion for a ship with inlet orifices at right angles to the direction of motion of ship is given by
A. [2(V_r - v) v]/ V_r²
B. 2(V_r + v) v]/ V_r²
C. [(V_r - v) v]/ V_r
D. [(V_r + v) v]/ V_r
Answer : A

18. According to fan laws, for fans having constant wheel diameter, the pressure varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : B

19. For small discharge at high pressure, following pump is preferred
A. Centrifugal
B. Axial flow
C. Mixed flow
D. Reciprocating
Answer : D

20. Power required to drive a centrifugal pump is directly proportional to ________ of its impeller.
A. Diameter
B. Square of diameter
C. Cube of diameter
D. Fourth power of diameter
Answer : D

21. Low specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : C

22. Which of the following pump is successfully used for lifting water to the turbines?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : C

23. The discharge through a reaction turbine with increase in unit speed
A. Increases
B. Decreases
C. Remain unaffected
D. First increases and then decreases
Answer : B

24. According to fan laws, at constant weight of air or gas, the speed, capacity and pressure vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : C

25. The overall efficiency for a Pelton wheel lies between
A. 0.50 to 0.65
B. 0.65 to 0.75
C. 0.75 to 0.85
D. 0.85 to 0.90
Answer : D

26. Which of the following hydraulic unit is used for transmitting increased or decreased torque to the driven shaft?
A. Hydraulic ram
B. Hydraulic intensifier
C. Hydraulic torque converter
D. Hydraulic accumulator
Answer : C

27. Puck up the wrong statement about centrifugal pump
A. Discharge a diameter
B. Head a speed²
C. Head a diameter
D. Power a speed?
Answer : A

28. If the ratio's of the corresponding forces acting at corresponding points are equal, then the model and the prototype are said to have.
A. Geometric similarity
B. Kinematic similarity
C. Dynamic similarity
D. None of these
Answer : C

29. A hydraulic accumulator is a device used to store ________ energy which may be supplied to a machine later on.
A. Strain
B. Pressure
C. Kinetic
D. None of these
Answer : B

30. Geometric similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : C

31. For centrifugal pump impeller, the maximum value of the vane exit angle is
A. 10° to 15°
B. 15° to 20°
C. 20° to 25°
D. 25° to 30°
Answer : C

32. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water would discharge
A. Same quantity of liquid
B. 0.75 Q
C. Q/0.75
D. 1.5 Q
Answer : A

33. Slip of a reciprocating pump is defined as the
A. Ratio of actual discharge to the theoretical discharge
B. Sum of actual discharge and the theoretical discharge
C. Difference of theoretical discharge and the actual discharge
D. Product of theoretical discharge and the actual discharge
Answer : C

34. Which of the following is not an impulse turbine?
A. Girad turbine
B. Turgo turbine
C. Pelton wheel
D. Kaplan turbine
Answer : D

35. The cavitation in a hydraulic machine is mainly due to
A. Low velocity
B. High velocity
C. Low pressure
D. High pressure
Answer : C

36. The unit power developed by a turbine is (where P = Power developed by the turbine under a head of water (H).
A. P/ ?H
B. P/ H
C. P/ H^3/2
D. P/ H²
Answer : C

37. A hydraulic ram is a device used to
A. Store the energy of water
B. Increase the pressure of water
C. To lift water from deep wells
D. To lift small quantity of water to a greater height when a large quantity of water is available at a smaller height
Answer : D

38. Maximum impulse will be developed in hydraulic ram when
A. Waste valve closes suddenly
B. Supply pipe is long
C. Supply pipe is short
D. Ram chamber is large
Answer : A

39. High specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. None of the above
Answer : A

40. The maximum efficiency of jet propulsion of a ship with inlet orifices at right angles to the direction of motion of ship, is
A. 40 %
B. 50 %
C. 60 %
D. 80 %
Answer : B

41. Axial flow pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : B

42. Overall efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : B

43. The maximum number of jets generally employed in impulse turbine without jet interference is
A. 4
B. 6
C. 8
D. 12
Answer : B

44. The centrifugal pump preferred for a specific speed between 80 to 160 r.p.m. is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with mixed flow at outlet
Answer : D

45. Medium specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : B

46. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit speed of the wheel is
A. 10 r.p.m.
B. 20 r.p.m.
C. 40 r.p.m.
D. 80 r.p.m.
Answer : B

47. A centrifugal pump will start delivering liquid only when the pressure rise in the impeller is equal to the
A. Kinetic head
B. Velocity head
C. Manometric head
D. Static head
Answer : C

48. Centrifugal pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : A

49. The relation between hydraulic efficiency (?_h), mechanical efficiency (?_m) and overall efficiency (?_o) is
A. ?_h = ?_o × ?_m
B. ?_m = ?_m × ?_h
C. ?_o = ?_h × ?_m
D. None of these
Answer : C

50. The flow rate in gear pump
A. Increases with increase in pressure
B. Decreases with increase in pressure
C. More or less remains constant with increase in pressure
D. Unpredictable
Answer : C