CEED - Hydraulics & Fluid Machineries 1000+ MCQ [Solved] PDF Download

1. Centrifugal pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : A

2. High specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. None of the above
Answer : A

3. The discharge through a reaction turbine with increase in unit speed
A. Increases
B. Decreases
C. Remain unaffected
D. First increases and then decreases
Answer : B

4. The discharge through a turbine is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

5. Francis, Kaplan and propeller turbines fall under the category of
A. Impulse turbines
B. Reaction turbines
C. Axial flow turbines
D. Mixed flow turbines
Answer : B

6. Reciprocating pumps are no more to be seen in industrial applications (in comparison to centrifugal pumps) because of
A. High initial and maintenance cost
B. Lower discharge
C. Lower speed of operation
D. Necessity of air vessel
Answer : A

7. The angle of taper on draft tube is
A. Greater than 15°
B. Greater than 8°
C. Greater than 5°
D. Less than 8°
Answer : D

8. The efficiency of a hydraulic press is given by (where W = Weight lifted by ram, P = Force applied on plunger, A = Area of ram, and a = Area of plunger)
A. (W/p) × (A/a)
B. (p/W) × (a/A)
C. (W/p) × (a/A)
D. (p/W) × (A/a)
Answer : C

9. Slip of a reciprocating pump is negative, when
A. Suction pipe is short and pump is running at low speeds
B. Delivery pipe is long and pump is running at high speeds
C. Suction pipe is short and delivery pipe is long and the pump is running at low speeds
D. Suction pipe is long and delivery pipe is short and the pump is running at high speeds
Answer : D

10. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. This saving in case of a single acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : C

11. A turbine pump is basically a centrifugal pump equipped additionally with
A. Adjustable blades
B. Backward curved blades
C. Vaned diffusion casing
D. Inlet guide blades
Answer : C

12. Which of the following is not an impulse turbine?
A. Girad turbine
B. Turgo turbine
C. Pelton wheel
D. Kaplan turbine
Answer : D

13. The optimum value of vane exit angle for a centrifugal pump impeller is
A. 10-15°
B. 20-25°
C. 30-40°
D. 50-60°
Answer : B

14. In axial flow fans and turbines, fluid enters and leaves as follows
A. Radially, axially
B. Axially, radially
C. Axially, axially
D. Radially, radially
Answer : C

15. Mechanical efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : A

16. The speed of an imaginary turbine, identical with the given turbine, which will develop a unit power under a unit head, is known as
A. Normal speed
B. Unit speed
C. Specific speed
D. None of these
Answer : C

17. Medium specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : B

18. Which of the following pump is successfully used for lifting water from deep wells?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : D

19. The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is _______ of the jet velocity,
A. One-fourth
B. One-half
C. Three-fourth
D. Double
Answer : B

20. In a centrifugal pump casing, the flow of water leaving the
A. Radial
B. Axial
C. Centrifugal
D. Vortex
Answer : D

21. When a piping system is made up primarily of vertical lift and very little pipe friction, the pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : C

22. In a Francis turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : D

23. Discharge (Q) of a centrifugal pump is given by (where D = Diameter of impeller at inlet, b = Width of impeller at inlet, and Vf = Velocity of flow at inlet)
A. Q = ?.D.Vf
B. Q = ?.b.Vf
C. Q = ?.D.bf.V
D. Q = D.b.Vf
Answer : C

24. The hydraulic efficiency of an impulse turbine is the
A. Ratio of the actual power produced by the turbine to the energy actually supplied by the turbine
B. Ratio of the actual work available at the turbine to the energy imparted to the wheel
C. Ratio of the work done on the wheel to the energy of the jet
D. None of the above
Answer : C

25. Which of the following is not a reaction turbine?
A. Fourneyron turbine
B. Journal turbine
C. Thomson's turbine
D. Pelton wheel
Answer : D

26. In an outward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : B

27. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water would discharge
A. Same quantity of liquid
B. 0.75 Q
C. Q/0.75
D. 1.5 Q
Answer : A

28. Slip of a reciprocating pump is defined as the
A. Ratio of actual discharge to the theoretical discharge
B. Sum of actual discharge and the theoretical discharge
C. Difference of theoretical discharge and the actual discharge
D. Product of theoretical discharge and the actual discharge
Answer : C

29. A jet of water is striking at the centre of a curved vane moving with a uniform velocity in the direction of jet. For the maximum efficiency, the vane velocity is ________ of the jet velocity
A. One-half
B. One-third
C. Two-third
D. Three-fourth
Answer : B

30. A turbine develops 10000 kW under a head of 25 metres at 135 r.p.m. Its specific speed is
A. 175.4 r.p.m.
B. 215.5 r.p.m.
C. 241.5 r.p.m.
D. 275.4 r.p.m
Answer : C

31. Discharge of a centrifugal pump is
A. Directly proportional to diameter of its impeller
B. Inversely proportional to diameter of its impeller
C. Directly proportional to (diameter)² of its impeller
D. Inversely proportional to (diameter)² of its impeller
Answer : D

32. The cavitation in reaction turbines is avoided, to a great extent by
A. Installing the turbine below the tail race level
B. Using stainless steel runner of the turbine
C. Providing highly polished blades to the runner
D. All of the above
Answer : D

33. The specific speed (Ns) of a centrifugal pump is given by
A. (N?Q)/H^2/3
B. (N?Q)/H^3/4
C. (N?Q)/H
D. (N?Q)/H^5/4
Answer : B

34. The speed of a turbine runner is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

35. The force exerted (in Newton) by a jet of water impinging normally on a fixed plate is (where w = Specific weight of water in N/m3, a = Crosssectional area of jet in m², and V = Velocity of jet in m/s)
A. waV / 2g
B. waV / g
C. waV² / 2g
D. waV² / g
Answer : D

36. The ratio of actual work available at the turbine to the energy imparted to the wheel is known as ________ efficiency.
A. Hydraulic
B. Mechanical
C. Overall
D. None of these
Answer : B

37. The speed ratio in case of Francis turbine varies from
A. 0.15 to 0.3
B. 0.4 to 0.5
C. 0.6 to 0.9
D. 1 to 1.5
Answer : C

38. Guide angle as per the aerofoil theory of Kaplan turbine blade design is defined as the angle between
A. Lift and resultant force
B. Drag and resultant force
C. Lift and tangential force
D. Lift and drag
Answer : A

39. Francis turbine is best suited for
A. Medium head application from 24 to 180 m
B. Low head installation up to 30 m
C. High head installation above 180 m
D. All types of heads
Answer : A

40. Saving of work done and power by fitting an air vessel to double acting reciprocating pump is of the order of
A. 39.2 %
B. 49.2 %
C. 68.8 %
D. 84.8 %
Answer : A

41. Which of the following turbine is preferred for a specific speed of 60 to 300 r.p.m.?
A. Pelton wheel
B. Francis turbine
C. Kaplan turbine
D. None of these
Answer : B

42. Maximum impulse will be developed in hydraulic ram when
A. Waste valve closes suddenly
B. Supply pipe is long
C. Supply pipe is short
D. Ram chamber is large
Answer : A

43. Head developed by a centrifugal pump is
A. Proportional to diameter of impeller
B. Proportional to speed of impeller
C. Proportional to diameter and speed of impeller
D. None of the above
Answer : C

44. A hydraulic accumulator is a device used to store ________ energy which may be supplied to a machine later on.
A. Strain
B. Pressure
C. Kinetic
D. None of these
Answer : B

45. The hydraulic efficiency of a reaction turbine, is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : C

46. In centrifugal pumps, maximum efficiency is obtained when the blades are
A. Straight
B. Bent forward
C. Bent backward
D. Radial
Answer : C

47. High specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. Any one of the above
Answer : C

48. The specific speed of a centrifugal pump, delivering 750 litres of water per second against a head of 15 metres at 725 r.p.m., is
A. 24.8 r.p.m.
B. 48.2 r.p.m
C. 82.4 r.p.m.
D. 248 r.p.m
Answer : C

49. A hydraulic accumulator normally consists of
A. Two cylinders, two rams and a storage device
B. A cylinder and a ram
C. Two coaxial rams and two cylinders
D. A cylinder, a piston, storage tank and control valve
Answer : B

50. The maximum efficiency of jet propulsion of a ship with inlet orifices at right angles to the direction of motion of ship, is
A. 40 %
B. 50 %
C. 60 %
D. 80 %
Answer : B