Hydraulics & Fluid Machineries MCQ Solved Paper for NEET

1. The flow ratio in case of Francis turbine varies from
A. 0.15 to 0.3
B. 0.4 to 0.5
C. 0.6 to 0.9
D. 1 to 1.5
Answer : A

2. Which of the following hydraulic unit is used for transmitting increased or decreased torque to the driven shaft?
A. Hydraulic ram
B. Hydraulic intensifier
C. Hydraulic torque converter
D. Hydraulic accumulator
Answer : C

3. A Francis turbine is used when the available head of water is
A. 0 to 25 m
B. 25 m to 250 m
C. Above 250 m
D. None of these
Answer : B

4. The working of which of the following hydraulic units is based on Pascal's law?
A. Air lift pump
B. Jet pump
C. Hydraulic coupling
D. Hydraulic press
Answer : D

5. The optimum value of vane exit angle for a centrifugal pump impeller is
A. 10-15°
B. 20-25°
C. 30-40°
D. 50-60°
Answer : B

6. If the ratios of all the corresponding linear dimensions are equal, then the model and the prototype are said to have
A. Geometric similarity
B. Kinematic similarity
C. Dynamic similarity
D. None of these
Answer : A

7. The maximum hydraulic efficiency of an impulse turbine is (where ? = Angle of blade tip at outlet)
A. (1 + cos ?)/2
B. (1 - cos ?)/2
C. (1 + sin ?)/2
D. (1 - sin ?)/2
Answer : A

8. In a Kaplan turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : B

9. Which of the following statement is wrong?
A. The reaction turbines are used for low head and high discharge.
B. The angle of taper on draft tube is less than 8°.
C. An impulse turbine is generally fitted slightly above the tail race.
D. A Francis turbine is an impulse turbine.
Answer : D

10. A hydraulic ram is a device used to
A. Store the energy of water
B. Increase the pressure of water
C. To lift water from deep wells
D. To lift small quantity of water to a greater height when a large quantity of water is available at a smaller height
Answer : D

11. The relation between hydraulic efficiency (?_h), mechanical efficiency (?_m) and overall efficiency (?_o) is
A. ?_h = ?_o × ?_m
B. ?_m = ?_m × ?_h
C. ?_o = ?_h × ?_m
D. None of these
Answer : C

12. Manometric head, in case of a centrifugal pump, is equal to
A. Suction lift + Loss of head in suction pipe due to friction + Delivery lift + Loss of head in delivery pipe due to friction + Velocity head in the delivery pipe
B. Workdone per kN of water Losses within the impeller
C. Energy per kN at outlet of impeller Energy per kN at inlet of impeller
D. All of the above
Answer : D

13. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit power of the wheel is
A. 0.25 kW
B. 0.75 kW
C. 1.75 kW
D. 3.75 kW
Answer : C

14. Dynamic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. None of the above
Answer : D

15. A turbine is required to develop 1500 kW at 300 r.p.m. under a head of 150 m. Which of the following turbine should be used?
A. Pelton wheel with one nozzle
B. Pelton wheel with two or more nozzles
C. Kaplan turbine
D. Francis turbine
Answer : A

16. Which type of the pump is different from others in the same group?
A. Screw pump
B. Gear pump
C. Cam and piston pump
D. Plunger pump
Answer : D

17. Guide angle as per the aerofoil theory of Kaplan turbine blade design is defined as the angle between
A. Lift and resultant force
B. Drag and resultant force
C. Lift and tangential force
D. Lift and drag
Answer : A

18. Which of the following pump is successfully used for lifting water to the turbines?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : C

19. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit speed of the wheel is
A. 10 r.p.m.
B. 20 r.p.m.
C. 40 r.p.m.
D. 80 r.p.m.
Answer : B

20. According to fan laws, at constant speed and capacity, the pressure and power vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : A

21. Saving of work done and power by fitting an air vessel to single acting reciprocating pump is of the order of
A. 39.2 %
B. 49.2 %
C. 68.8 %
D. 84.8 %
Answer : D

22. In an inward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : C

23. The width of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Double
B. Three times
C. Four times
D. Five times
Answer : D

24. In axial flow fans and turbines, fluid enters and leaves as follows
A. Radially, axially
B. Axially, radially
C. Axially, axially
D. Radially, radially
Answer : C

25. The efficiency of jet propulsion for a ship with inlet orifices at right angles to the direction of motion of ship is given by
A. [2(V_r - v) v]/ V_r²
B. 2(V_r + v) v]/ V_r²
C. [(V_r - v) v]/ V_r
D. [(V_r + v) v]/ V_r
Answer : A

26. Centrifugal pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : A

27. For centrifugal pump impeller, the maximum value of the vane exit angle is
A. 10° to 15°
B. 15° to 20°
C. 20° to 25°
D. 25° to 30°
Answer : C

28. In impulse Turbine, energy available at the inlet is in the form of
A. Potential Energy
B. Strain Energy
C. Kinetic energy
D. None of these
Answer : C

29. Which of the following statement is correct?
A. In an impulse turbine, the water impinges on the buckets with pressure energy.
B. In a reaction turbine, the water glides over the moving vanes with kinetic energy.
C. In an impulse turbine, the pressure of the flowing water remains unchanged and is equal to atmospheric pressure.
D. In a reaction turbine, the pressure of the flowing water increases after gliding over the vanes.
Answer : C

30. Medium specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : B

31. The jet ratio is defined as the ratio of the
A. Diameter of jet to the diameter of Pelton wheel
B. Velocity of jet to the velocity of Pelton wheel
C. Diameter of Pelton wheel to the diameter of jet
D. Velocity of Pelton wheel to the velocity of jet
Answer : C

32. Low specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. None of the above
Answer : A

33. The cavitation in a hydraulic machine is mainly due to
A. Low velocity
B. High velocity
C. Low pressure
D. High pressure
Answer : C

34. According to fan laws, for the fans having constant wheel diameters, the power demand varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : C

35. In an outward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : B

36. In a reaction turbine, the draft tube is used
A. To run the turbine full
B. To prevent air to enter the turbine
C. To increase the head of water by an amount equal to the height of the runner outlet above the tail race
D. To transport water to downstream
Answer : C

37. The specific speed of a turbine is given by the equation
A. N?P / H^3/2
B. N?P / H²
C. N?P / H^5/4
D. N?P / H³
Answer : C

38. Power required (in watts) to drive a centrifugal pump is (where H_m = Manometric head in metres, w = Specific weight in N/m³, Q = Discharge of the pump in m³/s, and ?_o = Overall efficiency of the pump)
A. (w H_m) / (Q × ?_o)
B. (w H_m Q) / ?_o
C. (w Q) / (H_m × ?_o)
D. (w Q ?_o) / H_m
Answer : B

39. Slip of a reciprocating pump is negative, when
A. Suction pipe is short and pump is running at low speeds
B. Delivery pipe is long and pump is running at high speeds
C. Suction pipe is short and delivery pipe is long and the pump is running at low speeds
D. Suction pipe is long and delivery pipe is short and the pump is running at high speeds
Answer : D

40. Maximum impulse will be developed in hydraulic ram when
A. Waste valve closes suddenly
B. Supply pipe is long
C. Supply pipe is short
D. Ram chamber is large
Answer : A

41. Low specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : C

42. In a centrifugal pump casing, the flow of water leaving the impeller, is
A. Rectilinear flow
B. Radial flow
C. Free vortex motion
D. Forced vortex
Answer : C

43. Kinematic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : A

44. A turbine pump is basically a centrifugal pump equipped additionally with
A. Adjustable blades
B. Backward curved blades
C. Vaned diffusion casing
D. Inlet guide blades
Answer : C

45. Francis, Kaplan and propeller turbines fall under the category of
A. Impulse turbines
B. Reaction turbines
C. Axial flow turbines
D. Mixed flow turbines
Answer : B

46. A ship with jet propulsion draws water through inlet orifices at right angles to the direction of its motion. The propelling force of the jet is (where a = Area of the jet, Vr = Relative velocity of the jet and ship = V + v, v = Velocity of the ship, and V = Velocity of the jet issuing from the ship)
A. waVr /g × (Vr + v)
B. waVr /g × (Vr - v)
C. waVr /g × (Vr + v)²
D. waVr /g × (Vr - v)²
Answer : B

47. Which place in hydraulic turbine is most susceptible for cavitations?
A. Inlet of draft rube
B. Blade inlet
C. Guide blade
D. Penstock
Answer : A

48. The undershot water wheels are those in which
A. The wheel runs entirely by the weight of water
B. The wheel runs entirely by the impulse of water
C. The wheel runs partly by the weight of water and partly by the impulse of water
D. None of the above
Answer : B

49. Slip of a reciprocating pump is defined as the
A. Ratio of actual discharge to the theoretical discharge
B. Sum of actual discharge and the theoretical discharge
C. Difference of theoretical discharge and the actual discharge
D. Product of theoretical discharge and the actual discharge
Answer : C

50. The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is _______ of the jet velocity,
A. One-fourth
B. One-half
C. Three-fourth
D. Double
Answer : B