GMAT - Hydraulics & Fluid Machineries 1000+ MCQ [Solved] PDF Download

1. In a centrifugal pump, the liquid enters the pump
A. At the top
B. At the bottom
C. At the canter
D. From sides
Answer : C

2. The flow rate in gear pump
A. Increases with increase in pressure
B. Decreases with increase in pressure
C. More or less remains constant with increase in pressure
D. Unpredictable
Answer : C

3. The power developed by a turbine is (where H = Head of water under which the turbine is working)
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : C

4. The number of buckets on the periphery of a Pelton wheel is given by
A. (D/2d) + 5
B. (D/2d) + 10
C. (D/2d) + 15
D. (D/2d) + 20
Answer : C

5. The width of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Double
B. Three times
C. Four times
D. Five times
Answer : D

6. Which of the following pump is generally used to pump highly viscous fluid?
A. Centrifugal pump
B. Reciprocating pump
C. Air lift pump
D. Screw pump
Answer : D

7. Air vessels in reciprocating pump are used to
A. Smoothen flow
B. Reduce acceleration to minimum
C. Increase pump efficiency
D. Save pump from cavitations
Answer : B

8. In an inward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : C

9. The specific speed of a turbine is given by the equation
A. N?P / H^3/2
B. N?P / H²
C. N?P / H^5/4
D. N?P / H³
Answer : C

10. An impulse turbine is used for
A. Low head of water
B. High head of water
C. Medium head of water
D. High discharge
Answer : B

11. Motion of a liquid in a volute casing of a centrifugal pump is an example of
A. Rotational flow
B. Radial
C. Forced spiral vortex flow
D. Spiral vortex flow
Answer : D

12. Geometric similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : C

13. According to fan laws, for fans having constant wheel diameter, the pressure varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : B

14. One horsepower is equal to
A. 102 watts
B. 75 watts
C. 550 watts
D. 735 watts
Answer : D

15. When a piping system is made up primarily of friction head and very little of vertical lift, then pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : B

16. The maximum number of jets generally employed in impulse turbine without jet interference is
A. 4
B. 6
C. 8
D. 12
Answer : B

17. In a reaction turbine, the draft tube is used
A. To run the turbine full
B. To prevent air to enter the turbine
C. To increase the head of water by an amount equal to the height of the runner outlet above the tail race
D. To transport water to downstream
Answer : C

18. If the net positive suction head (NPSH) requirement for the pump is not satisfied, then
A. No flow will take place
B. Cavitation will be formed
C. Efficiency will be low
D. Excessive power will be consumed
Answer : B

19. Slip of a reciprocating pump is negative, when
A. Suction pipe is short and pump is running at low speeds
B. Delivery pipe is long and pump is running at high speeds
C. Suction pipe is short and delivery pipe is long and the pump is running at low speeds
D. Suction pipe is long and delivery pipe is short and the pump is running at high speeds
Answer : D

20. The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is _______ of the jet velocity,
A. One-fourth
B. One-half
C. Three-fourth
D. Double
Answer : B

21. Which of the following pump is preferred for flood control and irrigation applications?
A. Centrifugal pump
B. Axial flow pump
C. Mixed flow pump
D. Reciprocating pump
Answer : B

22. The centrifugal pump preferred for a specific speed between 80 to 160 r.p.m. is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with mixed flow at outlet
Answer : D

23. Slip of a reciprocating pump is defined as the
A. Ratio of actual discharge to the theoretical discharge
B. Sum of actual discharge and the theoretical discharge
C. Difference of theoretical discharge and the actual discharge
D. Product of theoretical discharge and the actual discharge
Answer : C

24. In axial flow fans and turbines, fluid enters and leaves as follows
A. Radially, axially
B. Axially, radially
C. Axially, axially
D. Radially, radially
Answer : C

25. The undershot water wheels are those in which
A. The wheel runs entirely by the weight of water
B. The wheel runs entirely by the impulse of water
C. The wheel runs partly by the weight of water and partly by the impulse of water
D. None of the above
Answer : B

26. A jet of water is striking at the centre of a curved vane moving with a uniform velocity in the direction of jet. For the maximum efficiency, the vane velocity is ________ of the jet velocity
A. One-half
B. One-third
C. Two-third
D. Three-fourth
Answer : B

27. The unit discharge through the turbine is
A. Q/?H
B. Q/H
C. Q/H^3/2
D. Q/H²
Answer : A

28. The speed of a turbine runner is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

29. The specific speed of a hydraulic turbine depends upon
A. Speed and power developed
B. Discharge and power developed
C. Speed and head of water
D. Speed, power developed and head of water
Answer : D

30. Impulse turbine is generally fitted
A. At the level of tail race
B. Little above the tail race
C. Slightly below the tail race
D. About 2.5 m above the tail race to avoid cavitations.
Answer : B

31. Delivery head of a centrifugal pump is
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : C

32. The working of which of the following hydraulic units is based on Pascal's law?
A. Air lift pump
B. Jet pump
C. Hydraulic coupling
D. Hydraulic press
Answer : D

33. A hydraulic coupling belongs to the category of
A. Power absorbing machines
B. Power developing machines
C. Energy transfer machines
D. Energy generating machines
Answer : C

34. The force exerted by a jet of water (in a direction normal to flow) impinging on a fixed plate inclined at an angle ? with the jet is
A. waV/2g × sin?
B. waV/g × sin?
C. waV²/2g × sin2?
D. waV²/g × sin?
Answer : C

35. According to fan laws, at constant weight of air or gas, the speed, capacity and pressure vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : C

36. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water, the horse power required will be
A. Same
B. 0.75 B.H.P.
C. B.H.P./0.75
D. 1.5 B.H.P.
Answer : B

37. Centrifugal pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : A

38. The unit speed of the turbine runner is
A. N/?H
B. N/H
C. N/H^3/2
D. N/H²
Answer : A

39. The speed of an imaginary turbine, identical with the given turbine, which will develop a unit power under a unit head, is known as
A. Normal speed
B. Unit speed
C. Specific speed
D. None of these
Answer : C

40. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit speed of the wheel is
A. 10 r.p.m.
B. 20 r.p.m.
C. 40 r.p.m.
D. 80 r.p.m.
Answer : B

41. Which of the following is not an impulse turbine?
A. Girad turbine
B. Turgo turbine
C. Pelton wheel
D. Kaplan turbine
Answer : D

42. According to fan laws, at constant pressure, the speed capacity and power vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : B

43. Which type of the pump is different from others in the same group?
A. Screw pump
B. Gear pump
C. Cam and piston pump
D. Plunger pump
Answer : D

44. The cavitation in reaction turbines is avoided, to a great extent by
A. Installing the turbine below the tail race level
B. Using stainless steel runner of the turbine
C. Providing highly polished blades to the runner
D. All of the above
Answer : D

45. Guide angle as per the aerofoil theory of Kaplan turbine blade design is defined as the angle between
A. Lift and resultant force
B. Drag and resultant force
C. Lift and tangential force
D. Lift and drag
Answer : A

46. The hydraulic efficiency of an impulse turbine is the
A. Ratio of the actual power produced by the turbine to the energy actually supplied by the turbine
B. Ratio of the actual work available at the turbine to the energy imparted to the wheel
C. Ratio of the work done on the wheel to the energy of the jet
D. None of the above
Answer : C

47. Which of the following statement is wrong?
A. The reaction turbines are used for low head and high discharge.
B. The angle of taper on draft tube is less than 8°.
C. An impulse turbine is generally fitted slightly above the tail race.
D. A Francis turbine is an impulse turbine.
Answer : D

48. Medium specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : B

49. The discharge through a reaction turbine ________ with the increase in unit speed.
A. Decreases
B. Increases
C. Remain same
D. None of these
Answer : A

50. Which of the following is not a reaction turbine?
A. Fourneyron turbine
B. Journal turbine
C. Thomson's turbine
D. Pelton wheel
Answer : D