The ratio of maximum fluctuation of speed to the mean speed is called
Fluctuation of speed
Maximum fluctuation of speed
Coefficient of fluctuation of speed
None of these
Correct Answer :
C. Coefficient of fluctuation of speed
Related Questions
A chain comprises of 5 links having 5 joints. Is it kinematic chain?
Yes
No
It is a marginal case
Data are insufficient to determine it
In a gear having involute teeth, the normal to the involute is a tangent to the
Pitch circle
Base circle
Addendum circle
Dedendum circle
The power from the engine to the rear axle of an automobile is transmitted by means of
Worm and worm wheel
Spur gears
Bevel gears
Hooke's joint
Which of the following is an inversion of a single slider crank chain?
Pendulum pump
Oscillating cylinder engine
Rotary internal combustion engine
All of these
In a cone pulley, if the sum of radii of the pulleys on the driving and driven shafts is Constant, then
Open belt drive is recommended
Crossed belt drive is recommended
Both open belt drive and crossed belt drive is recommended
The drive is recommended depending upon the torque transmitted
An imaginary circle which by pure rolling action, gives the same motion as the actual gear, is called
Addendum circle
Dedendum circle
Pitch circle
Clearance circle
The relation between the controlling force (Fc) and radius of rotation (r) for a stable spring controlled governor is
Fc = ar + b
Fc = ar - b
Fc = ar
Fc = a/r + b
The secondary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, ω = Angular speed of crank, r = Radius of crank, θ = Angle of inclination of crank with the line of stroke, and n = Ratio of the length of connecting rod to radius of crank)
m.ω².r sinθ
m.ω².r cosθ
m.ω².r (sin 2θ/n)
m.ω².r (cos 2θ/n)
Which of the following statement is correct for gears?
The addendum is less than the dedendum
The pitch circle diameter is the product of module and number of teeth
The contact ratio means the number of pairs of teeth in contact
All of the above
The velocity of piston in a reciprocating steam engine is given by (where ω = Angular velocity of crank, r = Radius of crank pin circle, θ = Angle turned by crank from inner dead centre, and n = Ratio of length of connecting rod to the radius of crank)
ωr [sin θ + (sin 2θ/n)]
ωr [cos θ + (cos 2θ/n)]
ω²r [sin θ + (sin 2θ/n)]
ω²r [cos θ + (cos 2θ/n)]
A fixed gear having 200 teeth is in mesh with another gear having 50 teeth. The two gears are connected by an arm. The number of turns made by the smaller gear for one revolution of arm about the centre of bigger gear is
2
4
3
None of the above
In a mechanism, usually one link is fixed. If the fixed link is changed in a kinematic chain, then relative motion of other links
Will remain same
Will change
Could change or remain unaltered depending on which link is fixed
Will not occur
Two heavy rotating masses are connected by shafts of lengths l₁, l₂ and l₃ and the corresponding diameters are d₁, d₂ and d₃. This system is reduced to a torsionally equivalent system having uniform diameter d = d₁ of the shaft. The equivalent length of the shaft is
(l₁ + l₂ + l₃)/3
l = l₁ + l₂.(d₁/d₂)³ + l₂.(d₁/d₃)³
l = l₁ + l₂.(d₁/d₂)⁴ + l₃.(d₁/d₃)⁴
l₁ + l₂ + l₃
There are six gears A, B, C, D, E and F in a compound train. The numbers of teeth in the gears are 20, 60, 30, 80, 25 and 75 respectively. The ratio of angular speeds of the driven (F) to the driver (A) of the drive is
1/24
1/8
4/15
12
Which gear train is used for higher velocity ratios in a small space?
Simple gear train
Compound gear train
Reverted gear train
Epicyclic gear train
The tractive force is maximum or minimum when the angle of inclination of crank with the line of stroke (θ) is equal to
0° and 90°
90° and 180°
135° and 315°
270° and 360°
Governor is used in automobile to
Decrease the variation of speed
Maximize the fuel economy
Limit the vehicle speed
Maintain constant engine speed
If the pressure angle is __________, a reciprocating follower will jam in its bearings.
Small
Too small
Large
Too large
The instantaneous centre of a rigid thin disc rolling on a plane rigid surface is located at
The centre of the disc
The point of contact
An infinite distance on the plane surface
The point on the circumference situated vertically opposite to the contact point
The direction of linear velocity of any point on a link with respect to another point on the same link is
Parallel to the link joining the points
Perpendicular to the link joining the points
At 45° to the link joining the points
None of the above
A shaft has an attached disc at the centre of its length. The disc has its centre of gravity located at a distance of 2 mm from the axis of the shaft. When the shaft is allowed to vibrate in its natural bow-shaped mode, it has a frequency of vibration of 10 rad/s. When the shaft is rotated at 300 r.p.m., it will whirl with a radius of
2 mm
2.22 mm
2.50 mm
3.0 mm
The two elements of a pair are said to form a higher pair, when they
Have a surface contact when in motion
Have a line or point contact when in motion
Are kept in contact by the action of external forces, when in motion
Permit relative motion
Inertia force acts
Perpendicular to the acceleration force
Along the direction of acceleration force
Opposite to the direction of acceleration force
None of the above
In order to give a complete secondary balance of a multi-cylinder inline engine,
The algebraic sum of the secondary forces must be equal to zero
The algebraic sum of the couples about any point in the plane of the secondary forces must be equal to zero
Both (A) and (B)
None of these
The number of centers in a crank driven slider crank mechanism is
0
2
4
6
The frictional torque transmitted in a truncated conical pivot bearing, considering uniform pressure, is
(1/2). μ W cosecα (r₁ + r₂)
(2/3). μ W cosecα (r₁ + r₂)
(1/2). μ W cosecα [(r₁³ - r₂³)/(r₁² - r₂²)]
(2/3). μ W cosecα [(r₁³ - r₂³)/(r₁² - r₂²)]
The lower pairs are __________ pairs.
Self-closed
Force-closed
Friction closed
None of these
For two governors A and B, the lift of sleeve of governor A is more than that of governor B, for a given fractional change in speed. It indicates that
Governor A is more sensitive than governor B
Governor B is more sensitive than governor A
Both governors A and B are equally sensitive
None of the above
V-belts are usually used for
Long drives
Short drives
Long and short drives
None of these
A reed type tachometer use the principle of
Longitudinal vibration
Torsional vibration
Transverse vibration
Damped free vibration