Related Questions
What is the correct answer?
4
What is the peak factor of a triangular wave?
What is the correct answer?
4
What is expected when two 20 k a 1 watt resistor in parallel are use instead of one 10 k a 1 watt?
A. Provides higher current
D. Provides wider tolerance
What is the correct answer?
4
Which of the following is the statement of Ohm�s law?
A. Electric current is directly proportional to both voltage and resistance
B. Electric current varies directly as the voltage and inversely as the resistance
C. Electrical power is directly proportional to the resistance and inversely as the current squared
D. Electrical power is directly proportional to both voltage squared and the resistance
What is the correct answer?
4
A series-parallel combination of identical resistors will
A. Increase the power rating compared with one resistor alone
B. Increase the voltage rating compared with one resistor alone
C. Reduce the voltage rating compared with resistor alone
D. Result in an expensive circuit
What is the correct answer?
4
The presence of an electric current is made known by
What is the correct answer?
4
Which of the following is a common material used in wire-wound resistors?
What is the correct answer?
4
In a pure capacitancea
A. Current leads voltage by 90�
B. Current leads voltage by 180�
C. Current lags voltage by 90�
D. Current lags voltage by 180�
What is the correct answer?
4
If a capacitor is rated for 200V dca what is its effective ac working voltage?
What is the correct answer?
4
A gang capacitor is a variable capacitor in which capacitance is varied by changing the
D. Distance between plates
What is the correct answer?
4
Which waveform in which the rms value and the mean value are equal?
What is the correct answer?
4
An impedance given by 90 -45� is a/an ___ impedance.
What is the correct answer?
4
It is impossible to change the voltage across a capacitor instantlya as this would produce ___ current.
What is the correct answer?
4
In the 5-band method of capacitor color codinga the first band indicates
A. Temperature coefficient
What is the correct answer?
4
The reason why electrical appliances are connected in parallel.
A. It is a simple circuit
B. This makes the operation of appliances independent with each other
C. This results in reduced power consumption
What is the correct answer?
4
Which of the following is a preferred resistor value?
What is the correct answer?
4
For greater accuracya the value of phase angle should be determined from
What is the correct answer?
4
If the inductance is decreaseda the impedance of the circuit containing a resistor a capacitor and an inductor connected in series to an ac source
C. Decreases or increases
D. Decreasesa increases or remains the same
What is the correct answer?
4
A factor that states how much the resistance changes for a change in temperature?
C. Coefficient of temperature change
D. Temperature coefficient of resistance
What is the correct answer?
4
Which one of the following elements serves as a protection against overload?
What is the correct answer?
4
The result of rust in electrical (wire) connection is
What is the correct answer?
4
What is the efficiency under the conditions of maximum power transfer?
What is the correct answer?
4
Which of the following is the most popular waveform?
What is the correct answer?
4
Which of the following dielectric materials makes the lowest-capacitance capacitor?
What is the correct answer?
4
A trimmer is a variable capacitor in which capacitance is varied by changing the
C. Distance between plates
What is the correct answer?
4
A term used to express the amount of electrical energy stored in electrostatic field.
What is the correct answer?
4
A rheostat is a form of
What is the correct answer?
4
An inductance of 1 mH is
What is the correct answer?
4
What value of R is needed with a 0.05 F Cfor an RCtime constant of 0.02 s?
What is the correct answer?
4
What is the cross-sectional are of a conductor whose diameter is 0.001 inch?
What is the correct answer?
4
In Norton�s theorema the short circuit current is obtained by
A. Opening the load terminals
B. Shorting the load terminals
C. Opening the voltage source
D. Shorting the voltage source