Home
Current Affairs January 2024

What is the correct answer?

4

Bitumen completely dissolves in

A. Carbon bisulphide

B. Chloroform

C. Coal tar

D. All of these

Correct Answer :

D. All of these


Related Questions

What is the correct answer?

4

Percentage content of silica in window glass, is

A. 40 to 45

B. 50 to 55

C. 60 to 65

D. 70 to 75

What is the correct answer?

4

Bitumen completely dissolves in

A. Carbon bisulphide

B. Chloroform

C. Coal tar

D. All of these

What is the correct answer?

4

Pick up the correct statement from the following:

A. Steel produced by open hearth process is milder than that obtained by the Bessemer process

B. Engineers prefer open hearth steel for structural purpose as it is more homogenous

C. Basic Bessemer process is suitable for converting poor ore containing a large proportion of sulphur and phosphorus into steel

D. All the above

What is the correct answer?

4

Minimum required water cement ratio for a workable concrete, is

A. 0.30

B. 0.40

C. 0.50

D. 0.60

What is the correct answer?

4

Slacking of lime is affected by

A. Keeping it exposed to air

B. Immersing the lime in water

C. Crushing the lime lumps

D. None of these

What is the correct answer?

4

Which of the following is a mineral?

A. Basalt

B. Granite

C. Quartz

D. Syenite

What is the correct answer?

4

Non acid-resistant asbestos is:

A. Tremolite asbestos

B. Chrysotile asbestos

C. Amosite asbestos

D. None of these

What is the correct answer?

4

Portland pozzolana cement possesses

A. Higher resistance to chemical attack

B. Lower heat of hydration

C. Lower shrinkage on drying

D. All the above

What is the correct answer?

4

For preparing porcelains, the clay should be

A. Sufficiently pure

B. Of high degree of tenacity

C. Of good plasticity

D. All the above

What is the correct answer?

4

Asphalt is obtained from

A. Petroleum distillation

B. Bitumen distillation

C. Plastic distillation

D. None of these

What is the correct answer?

4

Pick up the incorrect statement from the following:

A. Hydraulic lime is generally obtained by burning kankar

B. Hydraulic lime sets slowly as compared to fat lime

C. Hydraulic lime is generally used in lime mortar

D. None of these

What is the correct answer?

4

Rapid hardening cement attains early strength due to

A. Larger proportion of lime grounded finer than normal cement

B. Lesser proportion of lime grounded coarser than normal cement

C. Lesser proportion of lime grounded finer than normal cement

D. Excess percentage of gypsum

What is the correct answer?

4

Refractory bricks resist

A. High temperature

B. Chemical action

C. Dampness

D. All the above

What is the correct answer?

4

For light and ornamental casting, the most unsuitable pig iron, is

A. Bessemer pig

B. Grey or foundry pig

C. White or forge pig

D. Mottled pig

What is the correct answer?

4

Vanadium steel is generally used for

A. Railway switches and crossing

B. Bearing balls

C. Magnets

D. Axles and springs

What is the correct answer?

4

Pick up the correct statement from the following:

A. Slaked lime contains calcium hydroxide

B. Quick lime contains calcium oxide

C. Slaked lime may be obtained from quick lime

D. All the above

What is the correct answer?

4

The type of steel used for precision levelling staff, is

A. Titanium steel

B. Carbon steel

C. Invar

D. Stainless steel

What is the correct answer?

4

Pick up the correct statement from the following:

A. Corrugated sheet iron is made by passing plain sheets between grooved rollers

B. Strength and stiffness of corrugated sheets are considerably increased

C. Corrugated sheets are generally used on slanting roofs

D. All the above

What is the correct answer?

4

Priming consists of

A. One part of white lead, 8 parts of chalk and four parts of twice boiled linseed oil

B. 8 parts of white lead, one part of chalk and four parts of twice boiled linseed oil

C. One part of white lead, 8 parts of chalk and one part of linseed oil

D. None to these

What is the correct answer?

4

Which one of the following is acid resistant asbestos?

A. Actinolite asbestos

B. Amosite asbestos

C. Anthophylite asbestos

D. All the above

What is the correct answer?

4

The cracks caused by shrinkage of the exterior surface of the wood exposed to atmosphere, are called:

A. Radial shakes

B. Heart shakes

C. Wind cracks

D. Twisted fibres

What is the correct answer?

4

During smelting process, the combination of fuel in the furnace

A. Forms carbon dioxide

B. Carbon dioxide with carbon forms carbon mono-oxide

C. Carbon mono-oxide reacts with Fe2O3 to form iron and liberates CO2

D. All the above

What is the correct answer?

4

Which of the following cements contains maximum percentage of dicalcium silicate?

A. Ordinary Portland cement

B. Low heat cement

C. Rapid hardening cement

D. Sulphate resisting cement

What is the correct answer?

4

For lime concrete,

A. Slump is 50 to 75 mm

B. Flexural strength at 90 days is 0.2 N/mm2

C. Compressive strength at 90 days is 1.5 N/mm2

D. All the above

What is the correct answer?

4

Cast iron is used for

A. Structural works in beams

B. Small sized water pipes

C. Columns and struts

D. None to these

What is the correct answer?

4

Which one of the following polymers is obtained from condensation polymerization?

A. Phenol formaldehyde

B. Carbamide

C. Melamine-formaldehyde

D. All of these

What is the correct answer?

4

For the manufacture of stainless steel, steel is mixed with

A. Chromium

B. Nickel

C. Tungsten

D. None of these

What is the correct answer?

4

Plywood has the advantage of

A. Greater tensile strength in longer direction

B. Greater tensile strength in shorter direction

C. Same tensile strength in all directions

D. None of the above

What is the correct answer?

4

The harmonious mixing of the clay ingredients, is known as

A. Weathering

B. Blending

C. Tempering

D. None of these

What is the correct answer?

4

Index number expressing the relative sizes of both coarse and fine aggregates, is called

A. Proportioning of aggregates

B. Fineness modulus

C. Grading of aggregates

D. None of these