Related Questions
What is the correct answer?
4
For ensuring quality of concrete, use
A. Single sized aggregates
What is the correct answer?
4
The depth of footing for an isolated column is governed by (i) Maximum bending moment (ii) Shear force (iii) Punching shear The correct answer is
D. All (i), (ii) and (iii)
What is the correct answer?
4
The grade of concrete M 150 means that compressive strength of a 15 cm cube after 28 days, is
What is the correct answer?
4
The approximate value of the ratio between direct tensile strength and flexural strength is
What is the correct answer?
4
In a pile of length l, the points of suspension from ends for lifting it are located at
What is the correct answer?
4
To minimise the effect of differential settlement, the area of a footing should be designed for
C. Dead load + fraction of live load
D. Live load + fraction of dead load
What is the correct answer?
4
The surface where two successive placements of concrete meet, is known as
What is the correct answer?
4
The process of proper and accurate measurement of concrete ingredients for uniformity of proportion, is known
What is the correct answer?
4
In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed as a cantilever The correct answer is
What is the correct answer?
4
If 1500 g of water is required to have a cement paste 1875 g of normal consistency, the percentage of water is,
What is the correct answer?
4
To obtain a very high strength concrete, use very fine grained
What is the correct answer?
4
According to IS: 4561978, the maximum reinforcement in a column is
What is the correct answer?
4
The produce impermeable concrete
A. Thorough mixing of concrete is required
B. Proper compaction of concrete is required
C. Proper curing of concrete is required
What is the correct answer?
4
The factor which affects workability, is
A. Water content and its temperature
B. Shape and size of the aggregates
What is the correct answer?
4
Pick up the correct statement from the following:
A. Lime in excess, causes the cement to expand and disintegrate
B. Silica in excess, causes the cement to set slowly
C. Alumina in excess, reduces the strength of the cement
What is the correct answer?
4
Joints in concrete structures, are provided
A. To reduce the tensile stresses likely to be developed due to evaporation of water
B. To minimise the change in the dimensions of the slab
C. To minimise the necessary cracking
What is the correct answer?
4
If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, 6 kg, 4 kg respectively, the fineness modulus of the aggregate, is
What is the correct answer?
4
Pick up the incorrect statement from the following:
A. Concrete for which preliminary tests are conducted, is called controlled concrete
B. Bulking of sand depends upon the fineness of grains
C. Concrete mix 1 : 6 : 12, is used for mass concrete in piers
What is the correct answer?
4
Le-Chatelier's apparatus is used for testing
What is the correct answer?
4
Pick up the correct proportions of chemical ingredients of cement
A. Lime : Silica : Alumina : Iron oxide : 63 : 22 : 6 : 3
B. Silica : Lime : Alumina : Iron oxide : 63 : 22 : 6 : 3
C. Alumina : Silica : Lime : Iron oxide : 63 : 22 : 6 : 3
D. Iron oxide : Alumina : Silica : Lime : 63 : 22 : 6 : 3
What is the correct answer?
4
For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than
What is the correct answer?
4
The grade of concrete not recommended by I.S. : 456, is
What is the correct answer?
4
For construction of structures in sea water, the cement generally preferred to, is
A. Portland-pozzolana cement
C. Low heat Portland cement
D. Rapid hardening cement
What is the correct answer?
4
If the foundations of all the columns of a structure are designed on the total live and dead load basis, then
A. There will be no settlement of columns
B. There will be no differential settlement
C. The settlement of exterior columns will be more than interior columns
D. The settlement of interior columns will be more than exterior columns
What is the correct answer?
4
The lower water cement ratio in concrete, introduces
A. Smaller creep and shrinkage
B. Greater density and smaller permeability
C. Improved frost resistance
What is the correct answer?
4
Examine the following statements: (i) Factor of safety for steel should be based on its yield stress, (ii) Factor of safety for steel should be based on its ultimate stress, (iii) Factor of safety for concrete should be based on its yield stress, (iv) Factor of safety for concrete should be based on its ultimate stress. The correct statements are
What is the correct answer?
4
M10 grade of concrete approximates
What is the correct answer?
4
Which of the following statements is incorrect?
A. Higher Vee-Bee time shows lower workability
B. Higher slump shows higher workability
C. Higher compacting factor shows higher workability
What is the correct answer?
4
If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be
D. Dependent on grade of concrete also
What is the correct answer?
4
The minimum percentage of chemical ingredient of cement is that of