What does a patch cable connect to within an Ethernet network?
The patch panel to the hub
The patch panel to the wall jack
The wall jack to the computer
The NIC directly to another computer's NIC
Correct Answer :
A. The patch panel to the hub
Related Questions
25 is used by SMTP
True.
False.
Class C network address class supports 65,534 hosts.
True.
False.
Which of the following can translate between dissimilar protocols and network types?
Hub
Repeater
Switch
Gateway
The key concern in the design of transmission system is -------------- and ---------------
data rate ,distance
speed, accuracy
accuracy, simplicity
distance , cost
Which of the following use default routes for inter domain routing?
Type 2
Type 4
Type 3
Type 1
When collection of various computers seems a single coherent system to its client, then it is called
computer network
distributed system
both (a and (b
none of the mentioned
If the organization allocates 10 bits as subnet number, to identify a physical network, then the organization can have at the most……………. networks and each of these networks that can support only…………………...hosts.
1022 networks, 62 hosts.
62 networks, 1022 hosts.
4094 networks, 14 hosts.
14 networks, 4094 hosts.
A network's Internet connection uses a 128-Kbps Basic Rate Interface (BRI). What type of connection is this?
DSL
Cable modem
ISDN
T1
What is the maximum length of twisted-pair cable before a signal booster is needed? Select all that apply.
25 meters
100 meters
328 feet
1000 feet
What are the subnet mask in dotted decimal notation for /20 networks?
255.255.252.0
255.255.255.0
255.255.254.0
255.255.240.0
In which of the following states after selecting a mailbox, actions can be taken against the
mail within the mailbox?
Non-authenticated state
Authenticated state
Selected state
Logout state
Which of the following is a media type that is most susceptible to interference?
Shielded twisted pair (STP)
Fiber optics
Unshielded twisted pair (UTP)
Coaxial
What is the range of multicast addressing?
223.0.0.0 through 240.255.255.255
244.0.0.0 through 239.255.255.266
224.1.1.1 through 239.555.255.255
224.0.0.0 through 239.255.255.255
How many number of host/machine can be attached to a network using a class B address?
65,536
128
256
16,777,216
Which of the following versions will replace IPv4 Internet layer?
IPv4.1
IPv5.1
IPv6
IPv5.2
Which of the following protocol was developed to overcome limitations of Routing
Information Protocol (RIP)?
Border Gateway Protocol (BGP)
Exterior Gateway Protocol (EGP)
Enhanced Interior Gateway Routing Protocol (EIGRP)
Open Shortest Path First (OSPF)
How many 64-Kbps channels are used on an ISDN BRI?
1
2
3
4
To communicate across a TCP/IP network, you must have a DNS server and DNS clients installed.
True.
False.
AppleTalk protocol configures hosts in zones on the network.
True.
False.
In ________ routing, the tunnel creates a bridge through areas that do not support
multicast traffic.
Internet
MBONE
Border Gateway Protocol
Multicast OSPF
Which directory service is used in Windows 2000 Server?
Active Directory
SAM
NDS
Bindery
Which of the following provides the service for any casting?
IPV5
IPV6
IPV7
IPV8
FDDI operates on 100 Mbps.
True.
False.
A network's Internet connection uses a 128-Kbps Basic Rate Interface (BRI). What type of connection is this?
DSL
Cable modem
ISDN
T1
You have a network card with the connector in question 43, and it also has a 15 pin female connector, the pins being in two rows. What type of card is it?
ethernet
token ring
arcnet
dlc
Strings enclosed in _______ quotation marks indicate single tokens.
Alphanumeric
Morse code
ASCII
Binary
Pure ALOHA has a maximum throughput of -----------
16.4 %
18.4 %
7.4 %
1 %
TCP protocol is responsible for logical addressing and delivery of packets.
True.
False.
You've taken your Windows 2000 laptop to a client's network and plugged it in. Your computer is configured for an IP network over 100BaseT using DHCP. You can't connect, even though the client says that DHCP is working on his 100BaseT network. What should
Use Ipconfig /release to release the old DHCP address.
Use Winipcfg and click Release to release the old DHCP address.
Use Ifconfig to initialize the NIC.
Use Tracert to determine the problem.
Data Transmission is not a layer in the OSI model
True.
False.