According to IS Specifications, the maximum pitch of rivets in compression is
Lesser of 200 mm and 12 t
Lesser of 200 mm and 16 t
Lesser of 300 mm and 32 t
Lesser of 3 00 mm and 24 t Where t is thickness of thinnest outside plate or angle
Correct Answer :
A. Lesser of 200 mm and 12 t
Related Questions
For the buildings having a low permeability, the internal wind pressure acting normal to the wall and roof surfaces is taken as
Zero
±0.2 p
± 0.5 p
±0.7 p Where p is basic wind pressure
The effect of racking forces is considered in the design of (i) Lateral braces (ii) Chord members The correct answer is
Only (i)
Only (ii)
Both (i) and (ii)
None of the above
If d is the distance between the flange angles,
Vertical stiffeners are provided in steel plate girders if the web is less than d/85
Vertical stiffeners are provided in high tensile steel plate girders if the web is less than d/175
Horizontal stiffeners are provided in steel plate girders if the web is less than d/200
All the above
For a compression member with double angle section, which of the following section will give larger value of minimum radius of gyration?
Equal angles back to back
Unequal legged angles with long legs back to back
Unequal legged angles with short legs back to back
Both (B) and (C)
Rivets connecting flange angles to cover plates in a plate girder are subjected to
Horizontal shear only
Vertical load only
Both (A) and (B)
None of the above
Steel tanks are mainly designed for
Weight of tank
Wind pressure
Water pressure
Earthquake forces
The allowable shear stress in the web of mild steel beams decreases with
Decrease in h/t ratio
Increase in h/t ratio
Decrease in thickness
Increase in height Where 'h' is height and t is thickness
For steel members not exposed to weather, the thickness of steel should not be less than
4.5 mm
6 mm
8 mm
10 mm
The effective length L of a simply supported beam with ends restrained against torsion, and also the ends of compression flange partially restrained against lateral bending, is given by
L = span
L = 0.85 span
L = 0.75 span
L = 0.7 span
If fbt and fc are the co-existent bending tensile stress and shear stress in a member, the equivalent stress fc is
√(fbt² + fc²)
√(fbt² + ½fc²)
√(fbt² + 3fc²)
√(fbt² - 3fc²)
When plates are exposed to weather, tacking rivets are provided at a pitch in line not exceeding (where t is the thickness of the outside plate).
8 t
16 t
24 t
32 t
The spans are considered approximately equal if the longest span does not exceed the shortest span by more than
5 %
10 %
15 %
20 %
The central deflection of a simply supported steel beam of length L with a concentrated load W at the centre, is
WL3/3EI
WL4/3EI
WL3/48EI
5WL4/384EI
The effective length of a weld, is taken as the actual length
Minus the size of weld
Minus twice the size of weld
Plus the size of weld
Plus twice the size of weld
Length of an outstanding leg of a vertical stiffener, may be taken equal to
1/10th of clear depth of the girder plus 15 mm
1/20th of clear depth of the girder plus 20 mm
1/25th of clear depth of the girder plus 25 mm
1/30th of clear depth of the girder plus 50 mm
The effective length of a compression member of length L held in position and restrained in direction at one end and effectively restrained in direction but not held in position at the other end, is
L
0.67 L
0.85 L
1.5 L
Shear buckling of web in a plate girder is prevented by using
Vertical intermediate stiffener
Horizontal stiffener at neutral axis
Bearing stiffener
None of the above
Rolled steel angle sections are classified as
Equal angles
Unequal angles
Bulb angles
All the above
The maximum tensile and compressive bending stress in extreme fibres of rolled I-sections and channels on the effective section, is
1500 kg/cm2
1420 kg/cm2
1650 kg/cm2
2285 kg/cm2
In rolled steel beams, shear force is mostly resisted by
Web only
Flanges only
Web and flanges together
None of these
According to IS Specifications, the maximum pitch of rivets in compression is
Lesser of 200 mm and 12 t
Lesser of 200 mm and 16 t
Lesser of 300 mm and 32 t
Lesser of 3 00 mm and 24 t Where t is thickness of thinnest outside plate or angle
Outstanding length of a compression member consisting of a channel, is measured as
Half of the nominal width
Nominal width of the section
From the edge to the first row of rivets
None of these
By providing sufficient edge distance, which of the following failures of riveted joint can be avoided?
Tension failure of the plate
Shear failure of the rivet
Shear failure of the plate
Crushing failure of the rivet
When the bolts are subjected to reversal of stresses, the most suitable type of bolt is
Black bolt
Ordinary unfinished bolt
Turned and fitted bolt
High strength bolt
The actual thickness of butt weld as compared to the thickness of plate is usually
More
Less
Equal
None of the above
Effective sectional area of a compression member is:
Gross sectional area - area of rivet hole
Gross sectional area + area of rivet hole
Gross sectional area × area of rivet hole
Gross sectional area + area of rivet hole
The rolled steel I-sections are most commonly used as beams because these provide
Large moment of inertia with less cross-sectional area
Large moment of resistance as compared to other section
Greater lateral stability
All the above
As per IS: 800, in the plastic design, which of the following pairs are correctly matched?
Working Loads Load factor
(i) Dead load 1.7
(ii) Dead Load + imposed load 1.7
(iii) Dead load + load due to wind or 1.3 seismic forces
(iv) Dead load + imposed load + load 1.7 due to wind or seismic forces
Of these statements
(i) and (ii) are correct
(i), (ii) and (iii) are correct
(ii) and (iii) are correct
Only (i) is correct
If the thickness of a structural member is small as compared to its length and width, it is classified as
One dimensional
Two dimensional
Three dimensional
None of these
A riveted joint may experience
Shear failure
Shear failure of plates
Bearing failure
All the above