Related Questions
What is the correct answer?
4
Chromium molybdenum steel cannot be welded using __________ welding.
What is the correct answer?
4
Resilience of a bolt can be increased by increasing its
What is the correct answer?
4
Which of the following is not a ferromagnetic material?
What is the correct answer?
4
__________ of test specimens is not involved in any hardness testing method.
What is the correct answer?
4
In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?
What is the correct answer?
4
Current employed in resistance welding ranges from __________ kVA/.
What is the correct answer?
4
Though tin occurs lower than iron in the electrochemical series, yet it is coated on steel for corrosion protection, because of its
C. Resistance to vegetable acids as the tin plate are commercially used in 'canning' industry
What is the correct answer?
4
Thermal equivalent of electrical power in practical calculation is __________ kcal/kWh.
What is the correct answer?
4
The most serious manufacturing defect from fracture toughness point of view is
What is the correct answer?
4
Compressed dry air is used as the cutting fluid, while machining
What is the correct answer?
4
Dies for wire drawing are generally made of
What is the correct answer?
4
Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.
A. Induced draft fan
B. Economiser
C. Air preheater
D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories?
What is the correct answer?
4
The minimum carbon content in steel should be __________ percent for it to respond to a hardening treatment.
What is the correct answer?
4
The most detrimental impurity in high pressure boiler feed water is
What is the correct answer?
4
Which of the following test is used for distinguishing among dry oils, semi-drying oils and non drying oils?
B. Reichert-Meissl value test
What is the correct answer?
4
Runge-Kutta method is used to solve a/an
A. Ordinary differential equation of nth order
B. Simultaneous non-linear equation
C. Linear differential equation
What is the correct answer?
4
With increase in compression ratio, the volumetric efficiency of air compressor
D. May increase or decrease (depends on the suction pressure)
What is the correct answer?
4
A cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is
What is the correct answer?
4
Alloy powder manufactured by the following process have spherical shapes.
A. Electrochemical deposition
What is the correct answer?
4
In the diving apparatus, helium is used along with oxygen, because it is
B. Not soluble in blood at high pressure
D. Completely miscible with oxygen
What is the correct answer?
4
In extrusion of metals, which of the following statement is true?
A. Speed of the extruded material is same as that of ram speed
B. Redundant work is a function of the die angle
C. Relative motion between the billet surface and the container wall is always present
D. Hollow ram is used for indirect extrusion
What is the correct answer?
4
Transition from laminar to turbulent zone in free convection heat transfer is governed by the critical value of
B. Grashoff number & Reynolds number
D. Grashoff number & Prandtl number
What is the correct answer?
4
For a spontaneous natural process at constant temperature and pressure, the free energy of the system always
D. Increases to a maximum before decreasing
What is the correct answer?
4
Water-tube boiler is the one, in which
A. Water passes through tubes and flue gases around it
B. Tube carrying hot flue gases are immersed in a pool of water
C. Tubes are placed in vertical position
What is the correct answer?
4
Glass reacts with
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.
What is the correct answer?
4
Tin based white metals are used, where bearings are subjected to
What is the correct answer?
4
In a drilling process, the metal is removed by both shearing & extrusion. General purpose drills are made of
What is the correct answer?
4
X-rays are
D. Of higher wavelength than visible light
What is the correct answer?
4
A jig is used while __________ a hole.