Related Questions
What is the correct answer?
4
A reduction in thermal resistance during heat transfer does not occur in the
A. Convection heat transfer by stirring the fluid and cleaning the heating surface
B. Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity
C. Radiation heat transfer by increasing the temperature and reducing the emissivity
What is the correct answer?
4
Which of the following is not a charge material for cupola?
What is the correct answer?
4
Pick out the wrong statement.
A. A soft magnetic material should have high permeability and small area of hysteresis loop
B. Poisson's ratio of high melting point metals is more than unity
C. Solders generally melt at less than 185°C
D. Steel produced by B.O.F process is ideally suited for manufacturing flat product
What is the correct answer?
4
Silicon crystal can be converted to p-type semiconductor by doping with
What is the correct answer?
4
A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre.
What is the correct answer?
4
In the diving apparatus, helium is used along with oxygen, because it is
B. Not soluble in blood at high pressure
D. Completely miscible with oxygen
What is the correct answer?
4
If a solid is compressed adiabatically in its elastic range, its __________ remains constant
What is the correct answer?
4
Tesla metre per ampere (T. m/A) is the unit for the measurement of
A. Magnetic susceptibility
C. Permeability of free space
What is the correct answer?
4
Which of the following materials has the maximum shrinkage allowance?
What is the correct answer?
4
Uniform ramming of sand in green sand moulding process leads to
A. Reduced chance of gas porosity
B. Greater dimensional stability of the casting
C. Uniform flow of molten metal into the mould cavity
D. Less sand expansion type of casting defect
What is the correct answer?
4
A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted will
D. May increase or decrease; depends on the thickness of each layer
What is the correct answer?
4
Biological shield in a nuclear reactor is generally provided to protect against the
What is the correct answer?
4
Dephosphorization of molten pig iron is favoured by
A. Oxidising and basic slag
B. Reducing and basic slag
C. High activity co-efficient of phosphorous in metal
D. Oxidising and neutral slag
What is the correct answer?
4
A 2 kg object weighs 1.8 kgf on a spring balance. The value of 'g' at that location in m/sec2 is
What is the correct answer?
4
Air standard Otto cycle is more efficient than the diesel cycle for the same
A. Heat addition & compression ratio
B. Heat addition & pressure
C. Compression ratio & pressure
D. Cylinder dimension & rpm
What is the correct answer?
4
Which of the following represents the correct time-temperature curve when a block of metal is heated above room temperature & then left to cool in the room following Newton's law of cooling in which the rate of temperature drop will go on decreasing with the passage of time.
What is the correct answer?
4
The capacity of a spring to store energy is called the spring form co-efficient. Stiffness of a spring is measured by the
A. Ability to absorb shock
B. Capacity to store energy
C. Ratio of the wire & coil diameters
D. Load to produce unit deflection
What is the correct answer?
4
Shampoos are commercially not available in the form of
What is the correct answer?
4
Limestone addition in the blast furnace is done to flux __________ present in the raw materials.
What is the correct answer?
4
Alloying elements present in Haynes stellite, which has superior performance than high speed steel, are:
A. Nickel, cobalt & chromium
B. Tungsten, chromium & cobalt
C. Manganese, chromium & cobalt
D. Tungsten, molybdenum & nickel
What is the correct answer?
4
Silicon in steel
A. Makes it usable in almost all magnetic circuits where alternating current is used
B. Increases its electrical resistivity and decreases the hysteresis loss
C. Is present upto 5% & 4% respectively when used in transformers & motor armatures
What is the correct answer?
4
For dynamic strain measurement, the Wheatstone bridge used is of __________ type.
A. Voltage sensitive null
B. Voltage sensitive deflected
C. Current sensitive deflected
What is the correct answer?
4
Lead is added to 60:40 brass primarily to improve
What is the correct answer?
4
Routing in production, planning & control is concerned with the
A. Sequence of operation to be performed
B. Progress of work performed
C. Authorisation of work to be performed
D. Balancing of load on machines
What is the correct answer?
4
Which of the following is not a principal alloying element for the structural steel?
What is the correct answer?
4
__________ metal is used as a bearing liner material.
What is the correct answer?
4
With increase in impurities in metals, their corrosion resistances
D. May increase or decrease; depending on the type of metal
What is the correct answer?
4
The atmospheric temperature during melting of ice/snow (in the atmosphere)
D. May increase or decrease; depends on the altitude where snow melts
What is the correct answer?
4
The most abundant metal present in the earth's crust is;
What is the correct answer?
4
Galvanic corrosion cannot be prevented by
C. Usage of largest possible anodic area