Related Questions
What is the correct answer?
4
Basic open hearth furnace (BOF) is not used for producing __________ steel.
What is the correct answer?
4
Half life of a radioactive isotope corresponds to the time required for half of the __________ to decay.
What is the correct answer?
4
The product (s) of roasting of a sulphide ore is (are)
D. Dependent on temperature and partial pressure of oxygen & sulphur dioxide
What is the correct answer?
4
The following thermocouple may be used for measuring temperature upto 1873°K.
C. Platinum-platinum rhodium
What is the correct answer?
4
Insulation of liquid surface can be achieved by __________ on top of its surface.
A. Floating hollow polypropylene spheres
B. Spraying alumina powder
What is the correct answer?
4
Shaft/rotor speed is most accurately measured by a
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.
What is the correct answer?
4
The order of a chemical reaction
A. Can be determined only experimentally
B. Can be determined from the stoichiometry of the reaction
What is the correct answer?
4
Main constituent of bone ash is
What is the correct answer?
4
A solid aluminium ball, when quenched in a water bath maintained at 40°C, cools down from 550°C to 450°C in 20 seconds. The expected temperature of the ball after next 20 seconds may be about __________ °C.
What is the correct answer?
4
Preheating before welding is done to
B. Burn oil & grease sticking to plate surfaces
C. Avoid plate distortion
What is the correct answer?
4
Lead is poured into the joints between two __________ pipes.
What is the correct answer?
4
Dies for wire drawing are generally made of
What is the correct answer?
4
In case of condensers & evaporators operating under given terminal conditions, LMTD (logarithmic mean temperature difference) for counter flow as compared to that for parallel flow is
What is the correct answer?
4
The difference between gross & net calorific values of fuel is due to the
A. Sensible heat carried away by the flue gases
B. Heat carried away by the steam from the moisture content of the fuel
C. Heat lost by radiation
D. Heat carried away by steam from the combustion of hydrogen in the fuel
What is the correct answer?
4
A cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is
What is the correct answer?
4
The elastic strain in copper is due to the
A. Motion of dislocations
B. Stretching of atomic bonds
C. Breakage of atomic bonds
What is the correct answer?
4
Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.
What is the correct answer?
4
__________ stress cannot be sustained by a fluid in equilibrium.
What is the correct answer?
4
Dislocation cross-slip is difficult in those materials, which have
A. Large number of slip systems
B. High work hardening rate
D. Low stacking fault energy
What is the correct answer?
4
Co-efficient of performance of a Carnot cycle refrigerator operating between - 23°C and + 27°C is
What is the correct answer?
4
On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the __________ of the input signal.
What is the correct answer?
4
The trace metal present in insulin is
What is the correct answer?
4
The malleability of a material is the property by virtue of which it can be rolled or hammered into thin sheets. Which of the following materials has the maximum malleability?
What is the correct answer?
4
A dummy activity is used in PERT network to describe the
A. Precedence relationship
What is the correct answer?
4
Force between the molecules of the same substance is called __________ force.
What is the correct answer?
4
Which of the following is not the commercial name of poly-methyl-methacrylate (PMMA)?
What is the correct answer?
4
Baffles provided on the shell side of a shell and tube heat exchanger are meant for
A. Providing support for the tubes
B. Improving heat transfer
D. Preventing the fouling of tubes & stagnation of shell side fluid
What is the correct answer?
4
The concentration of (H+) ions is 4 x 10-5 in a solution. Then pH of the solution will be (Given log 4 = 0.6)
What is the correct answer?
4
The critical pressure at which the latent heat of vaporisation of steam becomes zero is __________ Kg/cm2.