Shaft/rotor speed is most accurately measured by a

Question

Shaft/rotor speed is most accurately measured by a

A. Frequency counter

B. Tachometer

C. Strobometer

D. Speedometer

Share this question with your friends

Show all Chemical Engineering Basics MCQ

Comment

Constituents of stellite are

A. Zinc, copper & nickel

B. Cobalt, chromium & tungsten

C. Zinc, aluminium & nickel

D. Nickel, cobalt & vanadium

Discuss this answer

__________ stress cannot be sustained by a fluid in equilibrium.

A. Shear

B. Tensile

C. Compressive

D. None of these

Discuss this answer

Which of the following is not categorised as the ore agglomeration process?

A. Nodulising

B. Pelletising

C. Balling

D. Briquetting

Discuss this answer

Faraday's law of electrolysis is related to the

A. Cation speed

B. Atomic number of the cation

C. Equivalent mass of the electrolyte

D. None of these

Discuss this answer

Percentage of differential pressure lost in a Venturimeter with a tapering of 15° may be about

A. 1

B. 10

C. 25

D. 50

Discuss this answer

In chemical dehumidification process

A. Wet bulb temperature increases

B. Dry bulb temperature remains constant

C. Dew point temperature increases

D. Dry bulb temperature increases

Discuss this answer

The burnout heat flux in the nucleate boiling regime is not a function of the

A. Liquid density

B. Vapour density

C. Temperature difference

D. Heat of evaporation

Discuss this answer

What is the range of tempering temperature (°C) for most of the materials?

A. 75-100

B. 200-300

C. 350-450

D. 500-600

Discuss this answer

The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as

A. Rigid

B. Tough

C. Ductile

D. Plastic

Discuss this answer

Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?

A. Aluminium

B. Copper

C. Titanium

D. Stainless steel

Discuss this answer

The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.

A. 0

B. 100

C. 50

D. None of these

Discuss this answer

__________ of test specimens is not involved in any hardness testing method.

A. Fracture

B. Indentation

C. Wear

D. Scratch

Discuss this answer

Hardening of steel is not possible, unless it is heated __________ critical point.

A. Above the highest

B. Above the lowest

C. Between the first & second

D. Between the second & third

Discuss this answer

All the atoms of the world comprise of electrons, proton & neutron except that of __________ atom in which neutron is absent.

A. Deuterium

B. Hydrogen

C. Neon

D. Helium

Discuss this answer

Theoretical volume of oxygen required for complete combustion of 1Nm³ of acetylene, in oxyacetylene welding is __________ Nm³.

A. 0.5

B. 1

C. 1/3

D. 2.5

Discuss this answer

Work done by a/an __________ process is determined by ∫p. dv

A. Adiabatic

B. Quasi-static

C. Isothermal

D. Isentropic

Discuss this answer

Identify the correct statement.

A. Sphlerite is zinc oxide

B. The first law of the thermodynamics is stated as δE = δQ - δW

C. Lead can be produced in a blast furnace

D. T. ferrooxidans is a fungus that can be used for leaching chalcopyrite

Discuss this answer

Which of the following mainly decides the current to be employed is arc welding?

A. Electrode size

B. Plate thickness

C. Voltage across the arc

D. Welded portion length

Discuss this answer

Enzymes belong to the category of

A. Proteins

B. Carbohydrates

C. Vitamins

D. Fats

Discuss this answer

Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans?

A. Emissivity of pipe surface

B. Diameter & length of the pipe

C. Temperature of hot pipe surface & that of air in the room

D. None of these

Discuss this answer

Triple point of water is

A. 0°F

B. 492°R

C. 0°K

D. -273°C

Discuss this answer

An example of unsteady non uniform flow is the flow of liquid under pressure through a

A. Tapering pipe at constant flow rate

B. Tapering pipe at either decreasing or increasing flow rate

C. Long pipeline of constant diameter

D. None of these

Discuss this answer

Increasing sulphur content in pig iron tends to make it

A. Soft

B. Hard

C. Tough

D. Ductile & malleable

Discuss this answer

Fibre glass is a composite material of

A. Glass fibre in a polymer matrix

B. Glass fibre in a metallic matrix

C. Polymer fibre in a glassy matrix

D. Both 'b' & 'c'

Discuss this answer

Heat transfer by __________ is almost absent in case of fluidised bed drying operation.

A. Radiation

B. Conduction

C. Convection

D. Both (B) & (C)

Discuss this answer

As the fluid flow rate increases, the float of the Rotameter

A. Rises in the tube

B. Rotates at higher speed

C. Rotates at lower speed

D. Drops down in the tube

Discuss this answer

The most suitable material of construction for a sewer to carry sewage under high pressure is

A. Asbestos cement

B. Steel

C. Cement concrete

D. Stoneware

Discuss this answer

Pick out the wrong statement.

A. Geothermal energy is a non-conventional source of energy

B. Mass is converted into energy in both nuclear fission & fusion reaction

C. Inhalation of mercury vapour is not harmful for human beings

D. Inhalation of arsenic causes cancer

Discuss this answer

Propulsion of rocket follows from the

A. Newton's second law of motion

B. Newton's third law of motion

C. Law of projectiles

D. Archimedes principle

Discuss this answer

The difference between gross & net calorific values of fuel is due to the

A. Sensible heat carried away by the flue gases

B. Heat carried away by the steam from the moisture content of the fuel

C. Heat lost by radiation

D. Heat carried away by steam from the combustion of hydrogen in the fuel

Discuss this answer

Accepted Answer

C. Strobometer

Shaft/rotor speed is most accurately measured by a

Correct Answer :

Show all Chemical Engineering Basics MCQ

Related Questions

Constituents of stellite are

__________ stress cannot be sustained by a fluid in equilibrium.

Which of the following is not categorised as the ore agglomeration process?

Faraday's law of electrolysis is related to the

Percentage of differential pressure lost in a Venturimeter with a tapering of 15° may be about

In chemical dehumidification process

The burnout heat flux in the nucleate boiling regime is not a function of the

What is the range of tempering temperature (°C) for most of the materials?

The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as

Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?

The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.

__________ of test specimens is not involved in any hardness testing method.

Hardening of steel is not possible, unless it is heated __________ critical point.

All the atoms of the world comprise of electrons, proton & neutron except that of __________ atom in which neutron is absent.

Theoretical volume of oxygen required for complete combustion of 1Nm³ of acetylene, in oxyacetylene welding is __________ Nm³.

Work done by a/an __________ process is determined by ∫p. dv

Identify the correct statement.

Which of the following mainly decides the current to be employed is arc welding?

Enzymes belong to the category of

Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans?

Triple point of water is

An example of unsteady non uniform flow is the flow of liquid under pressure through a

Increasing sulphur content in pig iron tends to make it

Fibre glass is a composite material of

Heat transfer by __________ is almost absent in case of fluidised bed drying operation.

As the fluid flow rate increases, the float of the Rotameter

The most suitable material of construction for a sewer to carry sewage under high pressure is

Pick out the wrong statement.

Propulsion of rocket follows from the

The difference between gross & net calorific values of fuel is due to the

Also checkout

Shaft/rotor speed is most accurately measured by a

Correct Answer :

Show all Chemical Engineering Basics MCQ

Related Questions

Constituents of stellite are

__________ stress cannot be sustained by a fluid in equilibrium.

Which of the following is not categorised as the ore agglomeration process?

Faraday's law of electrolysis is related to the

Percentage of differential pressure lost in a Venturimeter with a tapering of 15° may be about

In chemical dehumidification process

The burnout heat flux in the nucleate boiling regime is not a function of the

What is the range of tempering temperature (°C) for most of the materials?

The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as

Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?

The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.

__________ of test specimens is not involved in any hardness testing method.

Hardening of steel is not possible, unless it is heated __________ critical point.

All the atoms of the world comprise of electrons, proton & neutron except that of __________ atom in which neutron is absent.

Theoretical volume of oxygen required for complete combustion of 1Nm3 of acetylene, in oxyacetylene welding is __________ Nm3.

Work done by a/an __________ process is determined by ∫p. dv

Identify the correct statement.

Which of the following mainly decides the current to be employed is arc welding?

Enzymes belong to the category of

Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans?

Triple point of water is

An example of unsteady non uniform flow is the flow of liquid under pressure through a

Increasing sulphur content in pig iron tends to make it

Fibre glass is a composite material of

Heat transfer by __________ is almost absent in case of fluidised bed drying operation.

As the fluid flow rate increases, the float of the Rotameter

The most suitable material of construction for a sewer to carry sewage under high pressure is

Pick out the wrong statement.

Propulsion of rocket follows from the

The difference between gross & net calorific values of fuel is due to the

Also checkout

Theoretical volume of oxygen required for complete combustion of 1Nm³ of acetylene, in oxyacetylene welding is __________ Nm³.