The bearings of heavy series have capacity ________ over the medium series.
20 to 30%
10 to 20%
30 to 40%
40 to 50%
Correct Answer :
A. 20 to 30%
Related Questions
The material used for brake lining should have __________ coefficient of friction.
Low
High
Moderate
None of these
Soderberg relation is based on __________ of the material whereas all other failure relation for dynamic loading are based on ultimate strength of the material.
Elastic strength
Yield strength
Shear strength
None of these
A sliding bearing in which although lubricant is present, the working surfaces __________ contact each other at least part of the time, is called boundary lubricated bearing.
Partially
Fully
Either A or B
None of these
When the screw in a mechanical screw jack rotates, the load kept on the top of it moves
Axially upwards
Axially downwards
Axially upwards or downwards
None of these
A compound cylinder with inner radius 50 mm and outer radius 70 mm is made by shrinking one cylinder on to the other cylinder, the junction radius is 60 mm and the junction pressure is 1.1 N/mm². The maximum hoop stress developed in the inner cylinder is
3.6 N/mm² compression
3.6 N/mm² tension
7.2 N/mm² compression
7.2 N/mm² tension
The piston rod of a steam engine is usually connected to the crosshead by means of
Bolted joint
Knuckle joint
Cotter joint
Universal joint
The stress which vary from a minimum value to a maximum value of the same nature (i.e. tensile or compressive) is called
Repeated stress
Yield stress
Fluctuating stress
Alternating stress
In the calculation of induced shear stress in helical springs, the Wahl's stress factor is used to take care of
Combined effect of transverse shear stress and bending stress in the wire
Combined effect of bending stress and curvature of the wire
Combined effect of transverse shear stress and curvature of wire
Combined effect of torsional shear stress and transverse shear stress in the wire
Yield point in fatigue loading as compared to static loading is
Same
Higher
Lower
Depends on other factors
According to Indian standards, total numbers of fundamental deviations are
10
15
20
25
When a beam of rectangular cross-section of width b and depth d, is subjected to a shear force F, the maximum shear stress induced will be
F/bh
3F/2bh
2F/bh
4F/bh
Which of the following key is preferred for the condition when a large amount of impact type torque is to be transmitted in both direction of rotation?
Woodruff key
Feather key
Gib-head key
Tangent key
A sliding bearing which can support steady loads without any relative motion between the journal and the bearing, is called
Hydrostatic lubricated bearing
Hydrodynamic lubricated bearing
Boundary lubricated bearing
Zero film bearing
The ratio of driving tensions for flat belts, neglecting centrifugal tension, is (where T₁, and T₂ = Tensions on the tight and slack sides of belt respectively, μ = Coefficient of friction, between the belt and pulley, and θ = Angle of contact)
T₁/T₂ = μθ
log (T₁/T₂) = μθ
T₁/T₂ =eμθ
T₁/T₂ = log μθ
Which of the following statement is wrong for a connecting rod?
The connecting rod will be equally strong in buckling about X-axis and Y-axis, if Ixx = 4 Iyy
If Ixx > 4 Iyy, the buckling will occur about Y-axis
If Ixx < 4 Iyy, the buckling will occur about X-axis
The most suitable section for the connecting rod is T-section
In order to avoid tearing of the plate at edge, the distance from the center line of the rivet hole to the nearest edge of the plate in terms of dia. of rivet d should be equal to
d
1.25 d
1.5 d
1.75 d
The maximum efficiency of a square threaded screw is
(1 - sinφ)/ (1 + sinφ)
(1 + sinφ)/ (1 - sinφ)
(1 - sinφ)/ (1 + cosφ)
(1 + cosφ)/ (1 - sinφ)
Which of the following screw thread is adopted for power transmission in either direction?
Acme threads
Square threads
Buttress threads
Multiple threads
In most machine members, the damping capacity of the material should be
Low
Zero
High
Could be anything
According to I.B.R., the distance between the rows of rivets, for equal number of rivets in more than one row for lap joint or butt joint (chain riveting) shall not be less than
d
1.5 d
2d
2.5 d
The load cup of a screw jack is made separate from the head of the spindle to
Prevent the rotation of load being lifted
Enhance the load carrying capacity of the jack
Reduce the effort needed for lifting the working load
Reduce the value of frictional torque
A single strap butt joint is always in __________ shear.
Single
Double
Triple share
None of these
Taper on the cotter and slot is provided
On both the sides
On one side only
On none of the sides
May be provided anywhere
Which of the following statement is correct for gears?
The pitch circle diameter is equal to the product of module and number of teeth
The addendum is less than dedendum
The pitch circle is always greater than the base circle
All of the above
Aircraft body is usually fabricated by
Welding
Pre-casting
Riveting
Casting
A tube has the following advantage over pipe
Lighter and easier to handle
Greater shock absorption
Smoother inside walls
All of the above
The expansion joint is mostly used for pipes which carry steam at __________ pressures.
Low
High
Medium
None of these
The stress induced in the belt is,
Tensile stress
Compressive stress
Direct shear stress
Torsional shear stress
For standard coarse threads of nut, the threads will be as strong in failure by shear as the bolt in tension, if the height of nut (h) is approximately
0.4 times
0.6 times
0.7 times
0.8 times
The suitable material for belt in agricultural machinery is
Leather
Rubber
Cotton duck
Balata gum