The ratio of maximum shear stress developed in a rectangular beam and a circular beam of the same cross-sectional area is
2/3
3/4
1
9/8
Correct Answer :
D. 9/8
Related Questions
Within elastic limit, stress is
Inversely proportional to strain
Directly proportional to strain
Square root of strain
Equal to strain
The efficiency and work ratio of a simple gas turbine cycle are
Low
Very low
High
Very high
The standard value of atmospheric pressure taken at sea level is
1.013 bar
760 mm of Hg
1013 × 102 N/m2
All of these
When a closely-coiled helical spring of mean diameter (D) is subjected to an axial load (W), the stiffness of the spring is given by
Cd⁴/D3n
Cd⁴/2D3n
Cd⁴/4D3n
Cd⁴/8D3n
The thermodynamic difference between a Rankine cycle working with saturated steam and the Carnot cycle is that
Carnot cycle can't work with saturated steam
Heat is supplied to water at temperature below the maximum temperature of the cycle
A Rankine cycle receives heat at two places
Rankine cycle is hypothetical
The neutral axis of the cross-section a beam is that axis at which the bending stress is
Zero
Minimum
Maximum
Infinity
The efficiency of Ericsson cycle is __________ Carnot cycle.
Greater than
Less than
Equal to
None of these
The unit of Young's modulus is
mm/mm
kg/cm
Kg
kg/cm²
In an ideal gas turbine plant, it is assumed that the compression and expansion processes are
Isothermal
Isentropic
Polytropic
None of these
A continuous beam is one which is
Fixed at both ends
Fixed at one end and free at the other end
Supported on more than two supports
Extending beyond the supports
Which of the following is a reversible non-flow process?
Isochoric process
Isobaric process
Hyperbolic process
All of these
In open cycle gas turbine plants
The indirect heat exchanger and cooler is avoided
Direct combustion system is used
A condenser is used
All of the above
The ultimate tensile stress of mild steel compared to ultimate compressive stress is
Same
More
Less
Unpredictable
When the expansion or compression takes place according to the law pvn = C, the process is known as
Isothermal process
Adiabatic process
Hyperbolic process
Polytropic process
One kilowatt is equal to
1 N-m/s
100 N-m
1000 N-m/s
1 × 106 N-m/s
In a tensile test, near the elastic limit zone, the
Tensile strain increases more quickly
Tensile strain decreases more quickly
Tensile strain increases in proportion to the stress
Tensile strain decreases in proportion to the stress
If the value of n = 0 in the equation pvn = C, then the process is called
Constant volume process
Adiabatic process
Constant pressure process
Isothermal process
Energy can neither be created nor destroyed, but it can be transformed from one form to another. This statement is known as
Zeroth law of thermodynamics
First law of thermodynamics
Second law of thermodynamics
Kinetic theory of gases
The molecular mass expressed in gram (i.e. 1 g - mole) of all gases, at N. T. P., occupies a volume of
0.224 litres
2.24 litres
22.4 litres
224 litres
A definite area or a space where some thermodynamic process takes place is known as
Thermodynamic system
Thermodynamic cycle
Thermodynamic process
Thermodynamic law
Carnot cycle consists of
Two constant volume and two isentropic processes
Two isothermal and two isentropic processes
Two constant pressure and two isentropic processes
One constant volume, one constant pressure and two isentropic processes
The state of stress at a point in a loaded member is shown in the below figure. The magnitude of maximum shear stress is
10 MPa
30 MPa
50 MPa
100 MPa
The ratio of specific heat at constant pressure (cp) and specific heat at constant volume (cv) is always __________ one.
Equal to
Less than
Greater than
None of these
When shear force at a point is zero, then bending moment is _________ at that point.
Zero
Minimum
Maximum
Infinity
The gas in cooling chamber of a closed cycle gas turbine is cooled at
Constant volume
Constant temperature
Constant pressure
None of these
Steam coal is a
Pulverised coal
Brown coal
Coking bituminous coal
Non-coking bituminous coal
When a bar is subjected to a change of temperature and its deformation is prevented, the stress induced in the bar is
Tensile stress
Compressive stress
Shear stress
Thermal stress
For a beam, as shown in the below figure, when the load W is applied in the centre of the beam, the maximum deflection is
Wl3 / 48EI
5Wl3 / 384EI
Wl3 / 392EI
Wl3 / 384EI
The ratio of maximum shear stress developed in a rectangular beam and a circular beam of the same cross-sectional area is
2/3
3/4
1
9/8
The value of gas constant (R) in S. I. units is
0.287 J/kgK
2.87 J/kgK
28.7 J/kgK
287 J/kgK