Related Questions
What is the correct answer?
4
A bolt
A. Has a head on one end and a nut fitted to the other
B. Has head at one end and other end fits into a tapped hole in the other part to be joined
C. Has both the ends threaded
D. Is provided with pointed threads
What is the correct answer?
4
A shaft is subjected to fluctuating loads for which the normal torque (T) and bending moment (M) are 1000 N-m and 500 N-m respectively. If the combined shock and fatigue factor for bending is 1.5 and combined shock and fatigue factor for torsion is 2, then the equivalent twisting moment for the shaft is
What is the correct answer?
4
If d is the normal diameter of a bolt in mm, then the initial tension in kg in a bolt used for making a fluid tight joint as for steam engine cover joint is calculated by the relation
What is the correct answer?
4
The velocity factor for ordinary cut gears operating at velocities upto 12.5 m/s is equal to
What is the correct answer?
4
Screws used for power transmission should have
What is the correct answer?
4
In a butt welded joint, the size of weld is __________ the throat of weld.
What is the correct answer?
4
A leaf spring in automobiles is used
D. To store strain energy
What is the correct answer?
4
Belt slip may occur due to
C. Driving pulley too small
What is the correct answer?
4
Tensile strength of a mild steel specimen can be roughly predicted from following hardness test
What is the correct answer?
4
In order to avoid tearing of the plate at an edge, the distance from the centre line of the rivet hole to the nearest edge of the plate should be equal to (where d = Diameter of rivet hole)
What is the correct answer?
4
Rivets are generally specified by
A. Thickness of plates to be riveted
What is the correct answer?
4
In cross or regular lay ropes
A. Direction of twist of wires in strands is opposite to the direction of twist of strands
B. Direction of twist of wires and strands are same
C. Wires in two adjacent strands are twisted in opposite direction
What is the correct answer?
4
A tap bolt
A. Has a head on one end and a nut fitted to the other
B. Has head at one end and other end fits into a tapped hole in the other part to be joined
C. Has both the ends threaded
What is the correct answer?
4
The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as
What is the correct answer?
4
In a steam engine, the piston rod is usually connected to the crosshead by means of a
What is the correct answer?
4
Aircraft body is usually fabricated by
What is the correct answer?
4
The taper on key is given on
What is the correct answer?
4
In order to permit the thermal expansion/contraction of tubing, it should be
What is the correct answer?
4
The difference between the tooth space and the tooth thickness as measured on the pitch circle, is called
What is the correct answer?
4
The bending moment M and a torque T is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then M is equal to
What is the correct answer?
4
If the size of a standard specimen for a fatigue testing machine is increased, the endurance limit for the material will
A. Have same value as that of standard specimen
What is the correct answer?
4
The stretching in a belt can be controlled by __________ the stress in the belt.
What is the correct answer?
4
The stress induced in the belt is,
D. Torsional shear stress
What is the correct answer?
4
Plastic flow in ductile materials
A. Increases the seriousness of static loading stress concentration
B. Lessens the seriousness of static loading stress concentration
D. Depends on other considerations
What is the correct answer?
4
The valve rod in a steam engine is connected to an eccentric rod by
What is the correct answer?
4
In levers, leverage is the ratio of
A. Load lifted to the effort applied
B. Mechanical advantage to the velocity ratio
C. Load arm to the effort arm
D. Effort arm to the load arm
What is the correct answer?
4
The washer is generally specified by its
What is the correct answer?
4
A circular shaft can transmit a torque of 5 kN-m. If the torque is reduced to 4 kN-m, then the maximum value of bending moment that can be applied to the shaft is
What is the correct answer?
4
A backing ring is used inside the pipe joint when making a
What is the correct answer?
4
Two shafts of the same length and material are joined in series. If the ratio of their diameters is 2, then the ratio of their angles of twist will be