The dedendum circle diameter is equal to (where φ = Pressure angle)
Pitch circle diameter × cosφ
Addendum circle diameter × cosφ
Clearance circle diameter × cosφ
Pitch circle diameter × sinφ
Correct Answer :
A. Pitch circle diameter × cosφ
Related Questions
In a full journal bearing, the angle of contact of the bearing with the journal is
120°
180°
270°
360°
A sliding bearing which can support steady loads without any relative motion between the journal and the bearing, is called
Hydrostatic lubricated bearing
Hydrodynamic lubricated bearing
Boundary lubricated bearing
Zero film bearing
In cross or regular lay ropes
Direction of twist of wires in strands is opposite to the direction of twist of strands
Direction of twist of wires and strands are same
Wires in two adjacent strands are twisted in opposite direction
Wires are not twisted
A sliding bearing in which although lubricant is present, the working surfaces __________ contact each other at least part of the time, is called boundary lubricated bearing.
Partially
Fully
Either A or B
None of these
Gear box is used
To produce torque
For speed reduction
To obtain variable speeds
To increase efficiency of system
The process which improves the machinability of steels, but lowers the hardness and tensile strength is
Normalising
Full annealing
Process annealing
Spheroidising
According to I.B.R., the distance between the rows of rivets, for equal number of rivets in more than one row for lap joint or butt joint (chain riveting) shall not be less than
d
1.5 d
2d
2.5 d
According to Indian standard specifications, a grey cast iron designated by 'FG 200' means that the
Carbon content is 2%
Maximum compressive strength is 200 N/mm²
Minimum tensile strength is 200 N/mm²
Maximum shear strength is 200 N/mm²
Endurance limit or fatigue limit is the maximum stress that a member can withstand for an infinite number of load applications without failure when subjected to
Dynamic loading
Static loading
Combined static and dynamic loading
Completely reversed loading
An open coiled helical compression spring 'A' of mean diameter 50 mm is subjected to an axial load W. Another spring 'B' of mean diameter 25 mm is similar to spring 'A' in all respects. The deflection of spring 'B' will be __________ as compared to spring 'A'.
One-eighth
One-fourth
One-half
Double
A connecting rod should be
Strong in buckling about X-axis
Strong in buckling about Y-axis
Equally strong in buckling about X-axis and Y-axis
Any one of the above
According to Indian standards, total numbers of tolerance grades are
8
12
18
20
Basic hole is one
Whose upper deviation is zero
Whose lower deviation is zero
Whose lower as well as upper deviations are zero
Does not exist
Which of the following statement is correct?
The cold rolled shafting is stronger than hot rolled shafting
The hot rolled shafting is stronger than cold rolled shafting
The cold rolled and hot rolled shaftings are equally strong
The shafts are not made by rolling process
The dedendum is the radial distance from the
Pitch circle to the top of a tooth
Pitch circle to the bottom of a tooth
Top of a tooth to the bottom of a tooth
Addendum circle to the clearance circle
In order to permit the thermal expansion/contraction of tubing, it should be
Crimped
Honed
Flared
Bent
An Involute pinion and gear are in mesh. If both have the same size of addendum, then there will be interference between the
Tip of the pinion and flank of gear
Tip of the gear and flank of pinion
Flanks of both gear and pinion
Tip of both gear and pinion
For a shaft diameter of 200 mm, the number of bolts in a marine flange coupling should be
8
6
4
10
The condition for maximum power transmission is that the maximum tension in the flat belt should be equal to
3 Pc
Pc
Pc/3
2 Pc Where, Pc = tension in belt due to centrifugal force
For a shoe brake, the equivalent coefficient of friction is equal to (where μ = Actual coefficient of friction, and θ = Semi-block angle)
2μ sinθ/(θ + sinθ)
μ sinθ/(2θ + sin 2θ)
4μ sinθ/(θ + sinθ)
4μ sinθ/(2θ + sin 2θ)
Auto frettage is the method of
Joining thick cylinders
Calculating stresses in thick cylinders
Pre-stressing thick cylinders
Increasing the life of thick cylinders
In designing a connecting rod, it is considered like __________ for buckling about X-axis.
Both ends hinged
Both ends fixed
One end fixed and the other end hinged
One end fixed and the other end free
A locking device extensively used in marine type connecting rod ends is a
Jam nut
Castle nut
Sawn nut
Ring nut
The cracks in helical springs used in railway carriages usually start on the inner side of the coil because of the fact that
It is subjected to a higher cyclic loading than the outer side
It is subjected to a higher stress than the outer side
It is more stretched than the outer side during the manufacturing process
It has a lower curvature than the outer side
An open belt drive is used when
Shafts are arranged at right angles and rotate in one definite direction
Shafts are arranged parallel and rotate in the opposite directions
Shafts are arranged parallel and rotate in the same directions
Driven shaft is to be started or stopped whenever desired without interfering with the driving shaft
The coefficient of friction between the belt and pulley depends upon the
Material of belt and pulley
Slip of belt
Speed of belt
All of these
In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft)
2d
3d
4d
5d
Coaxing is the procedure of increasing
Metal strength by cycling
Metal hardness by surface treatment
Metal resistance to corrosion by coating
Fatigue limit by overstressing the metal by successively increasing loadings
In hydrodynamic bearings
The oil film pressure is generated only by the rotation of the journal
The oil film is maintained by supplying oil under pressure
Do not require external supply of lubricant
Grease is used for lubrication
If shearing stress in nut is half the tensile stress in a bolt, then nut length should be equal to
Diameter of bolt
0.75 × diameter of bolt
1.25 × diameter of bolt
1.5 × diameter of bolt