The product of the diametral pitch and circular pitch is equal to
1
1/π
π
π × number of teeth
Correct Answer :
C. π
Related Questions
The design of the pressure vessel is based on
Longitudinal stress
Hoop stress
Longitudinal and hoop stress
None of these
In case of pressure vessels having closed ends, the fluid pressure induces
Longitudinal stress
Shear stress
Circumferential stress
None of these
Basic shaft is one
Whose upper deviation is zero
Whose lower deviation is zero
Whose lower as well as upper deviations are zero
Does not exist
A transmission shaft includes
Over head shaft
Counter shaft
Line shaft
All of these
In composite or reverse laid ropes
Direction of twist of wires in strands is opposite to the direction of twist of strands
Direction of twist of wires and strands are same
Wires in two adjacent strands are twisted in opposite direction
Wires are not twisted
When a bolt is subjected to shock loading, the resilience of the bolt should be considered in order to prevent breakage at the
Thread
Middle
Shank
Head
The largest diameter of an external or internal screw thread is known as
Minor diameter
Major diameter
Pitch diameter
None of these
The stretching in a belt can be controlled by __________ the stress in the belt.
Reducing
Increasing
Both A and B
None of these
During hot working of metals,
Porosity of the metal is largely eliminated
Grain structure of the metal is refined
Mechanical properties are improved due of refinement of grains
All of the above
A spring is used to
Measure forces
Apply forces
Store energy
All of these
Which is correct statement? Stress concentration in static loading is
Very serious in brittle materials and less serious in ductile materials
Very serious in ductile materials and less serious in brittle materials
Equally serious in both types of materials
Seriousness would depend on other factors
The velocity of sliding ________ the distance of the point of contact from the pitch point.
Is directly proportional to
Is inversely proportional to
Is equal to cos φ multiplied by
Does not depend upon
In order to obtain bolt of uniform strength
Increase shank diameter
Increase its length
Drill an axial hole through head up to threaded portion so that shank area is equal to root area of thread
Tighten die bolt properly
A connecting rod should be
Strong in buckling about X-axis
Strong in buckling about Y-axis
Equally strong in buckling about X-axis and Y-axis
Any one of the above
If a shaft made from ductile material is subjected to combined bending and twisting moment, calculations based on which one of the following failure theories will give the most conservative value?
Maximum principal stress theory
Maximum shear stress theory
Maximum strain energy theory
Maximum distortion energy theory
In an oil lubricated journal bearing, the coefficient of friction between the journal and the bearing
Remains constant at all speeds
Is minimum at zero speed and increases monotonically with increase in speed
Is maximum at zero speed and decreases monotonically with increase in speed
Becomes minimum at an optimum speed and then increases with further increase in speed
Which is correct statement? Stress concentration in cyclic loading is
Very serious in brittle materials and less serious in ductile materials
Very serious in ductile materials and less serious in brittle materials
Equally serious in both types of materials
Seriousness would depend on other factors
Oil in journal bearing should be applied at the point where load is
Nil or lightest
Maximum
Average
Any one of the above
The load cup of a screw jack is made separate from the head of the spindle to
Prevent the rotation of load being lifted
Enhance the load carrying capacity of the jack
Reduce the effort needed for lifting the working load
Reduce the value of frictional torque
Which of the following screw thread is adopted for power transmission in either direction?
Acme threads
Square threads
Buttress threads
Multiple threads
In worm, gears, pitch lead angle is
Half the angle between two inclined faces in axial plane
The angle between the tangent to the pitch helix and the plane of rotation
The angle between the tangent to the pitch helix and an element of the cylinder
None of the above
For a shoe brake, the equivalent coefficient of friction is equal to (where μ = Actual coefficient of friction, and θ = Semi-block angle)
2μ sinθ/(θ + sinθ)
μ sinθ/(2θ + sin 2θ)
4μ sinθ/(θ + sinθ)
4μ sinθ/(2θ + sin 2θ)
The value of Lewis form factor used in design of gears is
Dependent on number of teeth of a gear
Dependent on system of teeth
Independent of size of teeth
All of these
The number of slots in a 25 mm castle nut is
8
4
2
6
The piston pin bearings in heavy duty diesel engines are
Needle roller bearings
Tapered roller bearings
Spherical roller bearings
Cylindrical roller bearings
Two helical springs of the same material and of equal circular crosssection, length and number of turns, but having radii 80 mm and 40 mm, kept concentrically (smaller radius spring within the larger radius spring), are compressed between two parallel planes with a load W. The inner spring will carry a load equal to
W/2
2W/3
W/9
8W/9
In designing a connecting rod, it is considered like __________ for buckling about X-axis.
Both ends hinged
Both ends fixed
One end fixed and the other end hinged
One end fixed and the other end free
The rated life of a bearing varies
Directly as load
Inversely as square of load
Inversely as cube of load
Inversely as fourth power of load
If T is the actual number of teeth on a helical gear and φ is the helix angle for the teeth, then formative number of teeth is written as
T sec3φ
T sec²φ
T/sec3φ
T cosecφ
The effective stress in wire ropes during normal working is equal to the stress due to
Axial load plus stress due to bending
Acceleration/retardation of masses plus stress due to bending
Axial load plus stress due to acceleration/retardation
Bending plus stress due to acceleration/retardation