Related Questions
What is the correct answer?
4
The value of for air & most common gases can be safely assumed to be
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
Work done by a/an __________ process is determined by ∫p. dv
What is the correct answer?
4
The unit of gc is
What is the correct answer?
4
Thermal equivalent of electrical power in practical calculation is __________ kcal/kWh.
What is the correct answer?
4
__________ iron is produced by the annealing of white cast iron.
What is the correct answer?
4
Lead is poured into the joints between two __________ pipes.
What is the correct answer?
4
Alloys having more than 80% copper are generally more
C. Prone to season cracking
What is the correct answer?
4
The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe)
What is the correct answer?
4
Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30%?
What is the correct answer?
4
Removal of non-condensable from steam or other vapour is termed as the __________ process.
What is the correct answer?
4
__________ joint is usually used for joining cast iron pipes mostly used for temporary pipelines, where it may be necessary to dismantle & reassemble the pipeline very frequently.
What is the correct answer?
4
Brittleness induced due to the presence of sulphur in steel can be reduced by adding
What is the correct answer?
4
Consumable electrodes are used in the __________ welding.
What is the correct answer?
4
Fatigue resistance of a material is measured by the
B. Ultimate tensile strength
What is the correct answer?
4
Which of the following is an example of stress corrosion?
A. Season cracking of brass
B. Caustic embrittlement of steel
What is the correct answer?
4
Steel & cast iron pipes are produced by __________ casting.
What is the correct answer?
4
Breakeven point represents the condition, when the company runs under no profit no loss condition. In break even analysis, total cost comprises of fixed cost
What is the correct answer?
4
The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.
What is the correct answer?
4
Water-tube boiler is the one, in which
A. Water passes through tubes and flue gases around it
B. Tube carrying hot flue gases are immersed in a pool of water
C. Tubes are placed in vertical position
What is the correct answer?
4
For the Stoke's law to be valid in the case of a falling sphere in a fluid, the
A. Reynolds number (based on sphere diameter) should be < 1
B. Flow around the sphere should be in turbulent region
C. Sphere must be metallic
D. Fluid density should be constant
What is the correct answer?
4
The heat released by cooling one mole of copper from 400 K to room temperature (300 K) is (assume : Cp of copper is 23 J K-1mole-1)
What is the correct answer?
4
Basic open hearth furnace (BOF) is not used for producing __________ steel.
What is the correct answer?
4
__________ is the hardest material out of the following.
What is the correct answer?
4
Which of the following does not discharge the dust collected as a dry solid?
A. Electrostatic precipitator
D. Gravity settling chamber
What is the correct answer?
4
The refrigerant freon-12 is chemically
What is the correct answer?
4
Stellite is a __________ material.
D. Non-ferrous cast alloy cutting tool
What is the correct answer?
4
The best lubricants for a machine working at high temperature & load is
What is the correct answer?
4
Which of the following metals cannot be hot worked at room temperature?
What is the correct answer?
4
__________ temperature remains constant during adiabatic saturation process of unsaturated air.