Related Questions
What is the correct answer?
4
The concentration of (H+) ions is 4 x 10-5 in a solution. Then pH of the solution will be (Given log 4 = 0.6)
What is the correct answer?
4
Cemented carbide tools are not suitable for cutting
What is the correct answer?
4
While the bin cards are used in the effective stores management, the queuing theory is associated with the __________ time.
What is the correct answer?
4
__________ test is the appropriate test to determine whether a material is ductile or brittle.
What is the correct answer?
4
According to thermodynamic Fahrenheit scale, the fundamental interval between ice point to steam point is
What is the correct answer?
4
For preparation of porous bearings by powder metallurgy, preferred particle shape is
What is the correct answer?
4
The starting of a car takes time in winter, because the
A. Octane number of fuel is decreased
B. Fuel supply for ignition is not sufficient
C. Vaporisation of the fuel is decreased
D. Pour point of fuel decreases
What is the correct answer?
4
Moist climate is the most favourable factor in the site selection far a
What is the correct answer?
4
The only suitable method for hardening the low carbon steel is case hardening. Which of the following is a case hardening process?
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called
What is the correct answer?
4
Resilience of a bolt can be increased by increasing its
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
Depreciation of machines fails under the indirect expenses head. As per income tax regulations, it is calculated by the __________ method.
C. Multiple straight line
D. Sum of the years digit
What is the correct answer?
4
Pressure required to increase the density of water by about 1% is __________ atmosphere.
What is the correct answer?
4
The thermodynamic law, = constant, is not followed by the
A. Free expansion of an ideal gas
B. Adiabatic expansion of steam in turbine
C. Adiabatic compression of air
D. Ideal compression of air
What is the correct answer?
4
Milk is fat dispersed in water. It is an example of
What is the correct answer?
4
The condition of diffraction from a crystal is given by
What is the correct answer?
4
The mechanism which changes the value of manipulated variable in response to the output signal from the control unit is called the
C. Floating control action
What is the correct answer?
4
The swift cup test evaluates the following property of a sheet metal.
What is the correct answer?
4
Steels with high carbon equivalent have poor Weldability, because in these steels during welding
A. Carbon and other alloying elements get oxidised from the weld pool
B. Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld
C. Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld
D. Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld
What is the correct answer?
4
Oxyacetylene reducing flame is used while carrying out welding on
What is the correct answer?
4
Steel balls are manufactured by
What is the correct answer?
4
The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge)
What is the correct answer?
4
The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength.
What is the correct answer?
4
Which of the following commonly used condenser tube materials has the lowest thermal conductivity?
What is the correct answer?
4
Inertial forces are obtained, when the elastic forces are multiplied by __________ number.
What is the correct answer?
4
The most detrimental impurity in high pressure boiler feed water is
What is the correct answer?
4
Which of the following is a commonly used manometric liquid for low pressure range?
What is the correct answer?
4
Iron content in Indian iron ore is about __________ percent.
What is the correct answer?
4
Alloys having more than 80% copper are generally more
C. Prone to season cracking