For S.H.M. cam, the acceleration of the follower at the ends of the stroke and aimed stroke respectively, is
Maximum and zero
Zero and maximum
Minimum and maximum
Zero and minimum
Correct Answer :
A. Maximum and zero
Related Questions
The working depth of a gear is the radial distance from the
Pitch circle to the bottom of a tooth
Pitch circle to the top of a tooth
Top of a tooth to the bottom of a tooth
Addendum circle to the clearance circle
Which of the following statement is correct for involute gears?
The interference is inherently absent.
The variation in centre distance of shafts increases radial force.
A convex flank is always in contact with concave flank.
The pressure angle is constant throughout the teeth engagement.
The equation of motion for a single degree of freedom system with viscous damping is 4(dx²/dt²) + 9(dx/dt) + 16x. The damping ratio of the system is
9/8
9/82
9/16
9/128
The rotor of a ship rotates in clockwise direction when viewed from stern and the ship takes a left turn. The effect of gyroscopic couple acting on it will be
To raise the bow and stern
To lower the bow and stern
To raise the bow and lower the stern
To raise the stern and lower the bow
The frequency of damped vibrations with viscous damping is ________ the frequency of undamped vibrations.
More than
Less than
Same as
None of these
The critical speed of a shaft in revolution per second is __________ as that of natural frequency of transverse vibration.
Same
Different
Unpredictable
None of these
The coriolis component of acceleration is taken into account for
Slider crank mechanism
Four bar chain mechanism
Quick return motion mechanism
All of these
The example of successfully constrained motion is a
Motion of an I.C. engine valve
Motion of the shaft between a footstep bearing
Piston reciprocating inside an engine cylinder
All of the above
The two parallel and coplanar shafts are connected by gears having teeth parallel to the axis of the shaft. This arrangement is known as
Spur gearing
Helical gearing
Bevel gearing
Spiral gearing
A point B on a rigid link AB moves with respect to A with angular velocity ω rad/s. The radial component of the acceleration of B with respect to A, is (where vBA = Linear velocity of B with respect to A)
vBA × AB
vBA /AB
v²BA
v²BA /AB
The primary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, ω = Angular speed of crank, r = Radius of crank, θ = Angle of inclination of crank with the line of stroke, and n = Ratio of the length of connecting rod to radius of crank)
m.ω².r sinθ
m.ω².r cosθ
m.ω².r (sin 2θ/n)
m.ω².r (cos 2θ/n)
A point on a link connecting double slider crank chain traces a
Ellipse
Circle
Parabola
Hyperbola
In a mechanism, usually one link is fixed. If the fixed link is changed in a kinematic chain, then relative motion of other links
Will remain same
Will change
Could change or remain unaltered depending on which link is fixed
Will not occur
Two pulleys of radii r₁ and r₂ and at distance x apart are connected by means of a cross belt drive. The length of the belt is
π (r₁ + r₂) + [(r₁ + r₂)²/x] + 2x
π (r₁ + r₂) + [(r₁ - r₂)²/x] + 2x
π (r₁ - r₂) + [(r₁ - r₂)²/x] + 2x
π (r₁ - r₂) + [(r₁ + r₂)²/x] + 2x
The train value of a gear train is
Equal to velocity ratio of a gear train
Reciprocal of velocity ratio of a gear train
Always greater than unity
Always less than unity
If the pressure angle is __________, a reciprocating follower will jam in its bearings.
Small
Too small
Large
Too large
The fundamental equation for correct steering is (where φ and α = Angle through which the axis of the outer wheel and inner wheel turns respectively, c = Distance between the pivots of the front axles, and d = Wheel base)
sinφ + sinα = b/c
cosφ - sinα = c/b
cotφ - cotα = c/b
tanφ + cotα = b/c
In the two rotor system as shown in the below figure (I₁ < I₂), a node of vibration is situated 
Between I₁, and I₂ but nearer I₁
Between I₁, and I₂ but nearer to I₂
Exactly in the middle of the shaft
Nearer to I₁ but outside
Throw of a cam is the maximum distance of the follower from
Base circle
Pitch circle
Root circle
Prime circle
To transmit power from one rotating shaft to another whose axes are neither parallel nor intersecting, use?
Spur gear
Spiral gear
Bevel gear
Worm gear
A motor car moving at a certain speed takes a left turn in a curved path. If the engine rotates in the same direction as that of wheels, men due to centrifugal forc
The reaction on me inner wheels increases and on the outer wheels decreases
The reaction on the outer wheels increases and on the inner wheels decreases
The reaction on the front wheels increases and on the rear wheels decreases
The reaction on the rear wheels increases and on the front wheels decreases
The engine of an aeroplane rotates in clockwise direction when seen from the tail end and the aeroplane takes a turn to the left. The effect of gyroscopic couple on the aeroplane will be
To dip the nose and tail
To raise the nose and tail
To raise the nose and dip the tail
To dip the nose and raise the tail
The secondary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, ω = Angular speed of crank, r = Radius of crank, θ = Angle of inclination of crank with the line of stroke, and n = Ratio of the length of connecting rod to radius of crank)
m.ω².r sinθ
m.ω².r cosθ
m.ω².r (sin 2θ/n)
m.ω².r (cos 2θ/n)
In a four bar chain or quadric cycle chain
Each of the four pairs is a turning pair
One is a turning pair and three are sliding pairs
Two are turning pairs and two are sliding pairs
Three are turning pairs and one is a sliding pair
A fixed gear having 200 teeth is in mesh with another gear having 50 teeth. The two gears are connected by an arm. The number of turns made by the smaller gear for one revolution of arm about the centre of bigger gear is
2
4
3
None of the above
The velocity of the reciprocating roller follower when it has contact with the straight flanks of the tangent cam, is given by (where ω = Angular velocity of the cam shaft)
ω (r₁ r₂) sinθ
ω (r₁ + r₂) sinθ sec2θ
ω (r₁ r₂) cosθ
ω (r₁ + r₂) cosθ cosec2θ
In multi V-belt transmission, if one of the belt is broken, we have to change the
Broken belt
Broken belt and its adjacent belts
All the belts
There is no need of changing any one as remaining belts can take care of transmission of load
Which of the following would constitute a link?
Piston, piston rod and cross head
Piston and piston rod
Piston rod and cross head
Piston, crank pin and crank shaft
The mechanism forms a structure, when the number of degrees of freedom (n) is equal to
0
1
2
-1
In a spring controlled governor, when the controlling force ________ as the radius of rotation increases, it is said to be a stable governor.
Remains constant
Decreases
Increases
None of these