Related Questions
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
Solidification time of a molten metal in a casting is proportional to (where, V = volume of metal & A = its surface area; in the casting)
What is the correct answer?
4
Common salt is produced from sea water in India generally by the __________ method.
What is the correct answer?
4
Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter.
What is the correct answer?
4
Brinell Hardness Number (BHN) for talc is approximately in the range of
What is the correct answer?
4
'Ice point' is designated on Fahrenheit temperature scale by
What is the correct answer?
4
__________ of austenite decreases the hardenability in steel.
D. Dissolved elements (except cobalt)
What is the correct answer?
4
Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.
A. Induced draft fan
B. Economiser
C. Air preheater
D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories?
What is the correct answer?
4
Corrosion is
D. An uncontrollable phenomenon
What is the correct answer?
4
A polymer is termed as an 'elastomer', if its percentage elongation is more than 100%. An elastomer is termed as 'rubber' if its percentage elongation is more than __________ percent.
What is the correct answer?
4
Potable water means the water used for
D. Evaporation to produce steam
What is the correct answer?
4
The excess air required for the combustion of pulverised coal is of the order of about __________ percent.
What is the correct answer?
4
Ceramic compounds as compared to metallic compounds
B. Resist greater tensile stress at room temperature
C. Have higher melting temperature
D. Are better conductor of electricity at higher temperature
What is the correct answer?
4
Which of the following is an acidic constituent of B.F. slag?
A.
What is the correct answer?
4
Melting point & boiling points of liquid oxygen are respectively - 218.8°C & - 183°C, while the same for liquid nitrogen is - 210°C & - 195.8°C respectively. The difference in melting points of liquid oxygen & liquid nitrogen is not equal to 8.8
What is the correct answer?
4
Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.
What is the correct answer?
4
Oxyacetylene reducing flame is used while carrying out welding on
What is the correct answer?
4
What is the range of tempering temperature (°C) for most of the materials?
What is the correct answer?
4
Minimum thermal efficiency of a steam boiler may be around __________ percent
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called
What is the correct answer?
4
__________ pipe is the most suitable for carrying sanitary drainage.
B. Reinforced cement concrete
What is the correct answer?
4
Wood is a/an __________ material.
What is the correct answer?
4
All of the following alloying elements of steel increases hardness but sacrifice ductility, except
What is the correct answer?
4
Cassiterite is an ore of
What is the correct answer?
4
What happens, when SO2 is passed through a solution of H2S in water?
A. Precipitation of sulphur takes place
What is the correct answer?
4
__________ is the most suitable lubricant for drawing mild steel wires?
What is the correct answer?
4
__________ is the trade name assigned to a nonferrous cast alloy composed of cobalt, chromium & tungsten.
What is the correct answer?
4
The delivery pressure of boiler feed water pump compared to the boiler steam pressure is
What is the correct answer?
4
The diffusion co-efficient of Ni in Cu at 1000 K is 1.93 × 10-16 m2S-1 and it is 1.94 × 10-14 m2S- 1 at 1200 K. The activation energy (in k. J.mole-1) for the diffusion of Ni in Cu is
What is the correct answer?
4
LVDT used for displacement measurement is a/an __________ transducer.