Related Questions
What is the correct answer?
4
__________ of test specimens is not involved in any hardness testing method.
What is the correct answer?
4
In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the
What is the correct answer?
4
The most important requirement for aluminium industry is the availability of cheap
What is the correct answer?
4
Function of fusible plug in a boiler is to
A. Drain out water and sludge from the boiler during repair
B. Put off fire in the furnace when water level in the boiler falls to unsafe limit
C. Guard the boiler in case of abnormal rise in steam pressure
What is the correct answer?
4
Cold chisels hammers are made of
What is the correct answer?
4
Square steel key is normally strong in failure by shear & crushing. Keys are normally made of __________ steel bars.
What is the correct answer?
4
The material used for coating the welding electrode is termed as the
What is the correct answer?
4
Annealing of cast iron
A. Softens it to facilitate machining
B. Decreases the free carbon
C. Increases the strength
What is the correct answer?
4
As the fluid flow rate increases, the float of the Rotameter
B. Rotates at higher speed
C. Rotates at lower speed
D. Drops down in the tube
What is the correct answer?
4
Work study deals with the __________ study.
What is the correct answer?
4
When an isolated thermodynamic system executes a process,
B. Heat transfer takes place
C. Mass flow occurs across the boundary of the system
D. No chemical reaction takes place within the system
What is the correct answer?
4
Transition from laminar to turbulent zone in free convection heat transfer is governed by the critical value of
B. Grashoff number & Reynolds number
D. Grashoff number & Prandtl number
What is the correct answer?
4
Electrolytic reduction cell used for conversion of calcined Al2O3 to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to
A. Achieve very high purity of aluminium (99.9%)
B. Keep the electrolyte in liquid condition by the generation of heat
C. Electrolytically dissociate alumina
What is the correct answer?
4
Oxyacetylene reducing flame is used while carrying out welding on
What is the correct answer?
4
Chlorine acts as a bleaching agent only in the presence of
What is the correct answer?
4
Atomic __________ is a whole number for an element.
What is the correct answer?
4
Thermit welding uses the following energy source.
C. Energy of high velocity electrons
D. Heat generated by friction
What is the correct answer?
4
Babbitt lining is used on brass/bronze bearings to increase the
A. Antifriction properties
What is the correct answer?
4
Which of the following material handling equipments is not suitable for moving materials in varying paths?
What is the correct answer?
4
Liquor poisoning generally occurs due to the presence of __________ in it.
What is the correct answer?
4
If the head is doubled in & centrifugal pump, the power required will increase in the ratio of
What is the correct answer?
4
A solid aluminium ball, when quenched in a water bath maintained at 40°C, cools down from 550°C to 450°C in 20 seconds. The expected temperature of the ball after next 20 seconds may be about __________ °C.
What is the correct answer?
4
Steels with high carbon equivalent have poor Weldability, because in these steels during welding
A. Carbon and other alloying elements get oxidised from the weld pool
B. Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld
C. Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld
D. Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld
What is the correct answer?
4
Out of the following substances, one ton of __________ will store the maximum heat for a rise of 30°C in temperature.
What is the correct answer?
4
What is the percentage of chromium in 18-4-1 high speed steel?
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.
What is the correct answer?
4
With decrease in the grain size of a material, its creep resistance
D. Either (A) or (B); depends on the material
What is the correct answer?
4
Which of the following is normally not found in both the S.I. (petrol) & C.I. (diesel) engines?
What is the correct answer?
4
Which of the following metals cannot be hot worked at room temperature?
What is the correct answer?
4
Which of the following is not a principal alloying element for the structural steel?