Related Questions
What is the correct answer?
4
The amount of heat required to raise the temperature of the unit mass of gas through one degree at constant volume, is called
A. Specific heat at constant volume
B. Specific heat at constant pressure
What is the correct answer?
4
When a system changes its state from one equilibrium state to another equilibrium state, then the path of successive states through which the system has passed, is known as
What is the correct answer?
4
When cut-off ratio is __________ the efficiency of Diesel cycle approaches to Otto cycle efficiency.
What is the correct answer?
4
For a beam, as shown in the below figure, the deflection at C is (where E = Young's modulus for the beam material, and I = Moment of inertia of the beam section.
C. [Wa/(a√3) x EIl] x (l² - a²)3/2
What is the correct answer?
4
Which of the following has the minimum atomic mass?
What is the correct answer?
4
The heat flows from a cold body to a hot body with the aid of an external source. This statement is given by
What is the correct answer?
4
Kelvin-Planck's law deals with
C. Conversion of heat into work
D. Conversion of work into heat
What is the correct answer?
4
Strain is defined as the ratio of
A. Change in volume to original volume
B. Change in length to original length
C. Change in cross-sectional area to original cross-sectional area
What is the correct answer?
4
A cycle consisting of two constant pressure and two isentropic processes is known as
What is the correct answer?
4
When two plates are butt together and riveted with cover plates with two rows of rivets, the joint is known as
C. Single riveted single cover butt joint
D. Double riveted double cover butt joint
What is the correct answer?
4
Efficiency of a riveted joint is the ratio of its strength (max. load it can resist without failure) to the strength of the un-punched plate in
What is the correct answer?
4
The thermodynamic difference between a Rankine cycle working with saturated steam and the Carnot cycle is that
A. Carnot cycle can't work with saturated steam
B. Heat is supplied to water at temperature below the maximum temperature of the cycle
C. A Rankine cycle receives heat at two places
D. Rankine cycle is hypothetical
What is the correct answer?
4
Strain is equal to (where l = Original length, and δl = Change in length)
What is the correct answer?
4
In an isothermal process,
A. There is no change in temperature
B. There is no change in enthalpy
C. There is no change in internal energy
What is the correct answer?
4
Percentage reduction in area performing tensile test on cast iron may be of the order of
What is the correct answer?
4
The measurement of a thermodynamic property known as temperature is based on
A. Zeroth law of thermodynamics
B. First law of thermodynamics
C. Second law of thermodynamics
What is the correct answer?
4
The absolute zero temperature is taken as
What is the correct answer?
4
A circular shaft fixed at, A has diameter D for half of its length and diameter D/2 over the other half, as shown in the below figure. If the rotation of B relative to A is 0.1 radian, the rotation of C relative to B will be
What is the correct answer?
4
Principal planes are planes having
What is the correct answer?
4
The amount of heat required to raise the temperature of 1 kg of water through one Kelvin is called
A. Specific heat at constant volume
B. Specific heat at constant pressure
What is the correct answer?
4
Formula based on IS codes is based on
What is the correct answer?
4
High air-fuel ratio in gas turbines
A. Increases power output
B. Improves thermal efficiency
C. Reduces exhaust temperature
D. Do not damage turbine blades
What is the correct answer?
4
A fletched beam is used to
A. Change the shape of the beam
B. Effect the saving in material
C. Equalise the strength in tension and compression
D. Increase the cross-section of the beam
What is the correct answer?
4
Which of the following cycles is not a reversible cycle?
What is the correct answer?
4
The tensile strength of the welded joint for double fillet is (where s = Leg or size of the weld, l = Length of weld, and σt = Allowable tensile stress for weld metal)
What is the correct answer?
4
According to Euler's column theory, the crippling load for a column of length (l) with one end fixed and the other end free is __________ the crippling load for a similar column hinged at both the ends.
What is the correct answer?
4
The given figure shows the Mohr's circle of stress for two unequal and like principal stresses (σx and σy) acting at a body across two mutually perpendicular planes. The normal stress on an oblique section making an angle θ with the minor principle plane is given by
What is the correct answer?
4
The behaviour of a perfect gas, undergoing any change in the variables which control physical properties, is governed by
What is the correct answer?
4
The thickness of a thin cylindrical shell with hemispherical ends is __________ that of spherical ends.
What is the correct answer?
4
The property of a material by virtue of which a body returns to its original, shape after removal of the load is called