Related Questions
What is the correct answer?
4
Vertical construction joints are provided where the shearing forces are minimum in the case of
What is the correct answer?
4
The opening provided in sloping roof with its top parallel to the roof surface, is called
What is the correct answer?
4
The arrangement of supporting an existing structure by providing supports underneath, is known as
What is the correct answer?
4
Pick up the correct statement about silt soil from the following:
A. The silt soil has particle size from 0.02 mm to 0.06 mm
B. In organic fine grained silt soil possesses no plasticity
C. The least plastic type normally consists of more or less equidimensional grains of quartz
What is the correct answer?
4
In any good staircase, the maximum and minimum pitch respectively should be
What is the correct answer?
4
The brick laid with its length parallel to the face of a wall, is a known as
What is the correct answer?
4
The taper of precast concrete pile should not be more than
What is the correct answer?
4
Ornamental moulded course placed on the top of a wall, is
What is the correct answer?
4
The 19 cm × 9 cm side of a brick as seen in the wall face, is generally known as
What is the correct answer?
4
The lower edge of the pitched roof, from where the rain water of the roof surface drops down, is known as
What is the correct answer?
4
The sill of a common wooden partition is
A. Vertical wooden member on either end
B. Lower horizontal wooden member
C. Upper horizontal wooden member
D. Intermediate horizontal wooden member
What is the correct answer?
4
Pick up the commonly adopted geophysical method in civil engineering from the following:
B. Electrical resistivity method
D. Both (a) and (b) of the above
What is the correct answer?
4
A wooden block fixed on back side of a door frame on its post, is known as
What is the correct answer?
4
The process of working a flat for the finishing coat, is known
What is the correct answer?
4
The function of cleats in a roof truss is
A. To support the common rafter
C. To prevent the purlins from tilting
What is the correct answer?
4
Stud(s) of a common wooden partition
A. Are vertical wooden members
B. Is the upper horizontal wooden member
C. Is the lower horizontal wooden member
D. Are the intermediate horizontal wooden members
What is the correct answer?
4
In horizontal D.P.C, thickness of cement concrete (1 : 2 : 4) is
What is the correct answer?
4
In case of foundations on sandy soil, maximum permissible differential settlement, is usually limited to
What is the correct answer?
4
The compaction of concrete in the drilled pile hole is done by compressed air in the case of
What is the correct answer?
4
The pile which is provided with a bulb filled with concrete at its lower end, is known as
What is the correct answer?
4
The bearing capacity of granite is generally
What is the correct answer?
4
To ensure that supporting area of an offset footing of a boundary wall is fully compressive, the C.G. of load must act
A. At the centre of the base
B. Within the middle third of the base
C. Within the middle fifth of the base
D. Neither (a), (b) nor (c)
What is the correct answer?
4
The foundation which consists of a thick reinforced cement slab covering whole area to support heavy concentrated structural loads, is known as
What is the correct answer?
4
The minimum strength of the mortar used in load bearing brick masonry, is
What is the correct answer?
4
For brick construction, the lime-sand mortar, is
What is the correct answer?
4
The line of intersection of the surfaces of a sloping roof forming an external angle exceeding 180°, is
What is the correct answer?
4
The highest line of sloping roof, where two opposite slopes meet, is known as
What is the correct answer?
4
The depth of excavation of foundations, is generally measured with a
What is the correct answer?
4
As compared to stretcher course, the thickness of joints in header course should be
What is the correct answer?
4
Couple roof is used for spans
B. 3.5 m but less than 5 m
C. 5 m but less than 6.5 m
D. 6.5 m but less than 8 m