Related Questions
What is the correct answer?
4
A mandrel is used to hold
What is the correct answer?
4
The cutting speed for drilling aluminium, brass and bronze with carbon steel drills is _________ cutting speed for drilling mild steel with high speed steel drills.
What is the correct answer?
4
The depth of cut in drilling is __________ the drill diameter.
What is the correct answer?
4
What is the name of the device used in arc welding circuits for the purpose of modifying the rate of current change when the weld road is varied rapidly?
What is the correct answer?
4
In a milling operation, two side milling cutters are mounted with a desired distance between them so that both sides of a workpiece can be milled simultaneously. This set up is called
What is the correct answer?
4
The rear teeth of a broach
A. Perform burnishing operation
What is the correct answer?
4
The method of grinding used to produce internal cylindrical holes and tapers, is
A. Internal cylindrical grinding
C. External cylindrical grinding
What is the correct answer?
4
The tool may fail due to
A. Cracking at the cutting edge due to thermal stresses
B. Chipping of the cutting edge
C. Plastic deformation of the cutting edge
What is the correct answer?
4
With the same tool life, the maximum material per minute is removed by
A. Increasing the cutting speed
B. Decreasing the cutting speed
C. Increasing the depth of cut
D. Increasing the feed rate
What is the correct answer?
4
While current is shut down in the welding circuit, what kind of voltage exists between the output terminals of the welding machine?
What is the correct answer?
4
The point angle of a drill, for drilling stainless steel, is
What is the correct answer?
4
Climb milling is chosen while machining because
A. The chip thickness increase gradually
B. It enables the cutter to dig in and start the cut
C. The specific power consumption is reduced
D. Better surface finish can be obtained
What is the correct answer?
4
A single point thread cutting tool should ideally hav
What is the correct answer?
4
The average cutting speed for turning mild steel with a high speed steel tool is
What is the correct answer?
4
Which of the following statement is correct about hot machining?
A. It requires less power than machining metals at room temperature.
B. The rate of tool wear is lower.
C. It is used for machining high strength and high temperature resistant materials.
What is the correct answer?
4
A lead-screw with half nuts in a lathe, free to rotate in both directions has
What is the correct answer?
4
The ratio between two consecutive spindle speeds for a six-speed drilling machine using drills of diameter 6.25 to 25 mm size and at a cutting velocity of 18 m/min is
What is the correct answer?
4
A CNC vertical milling machine has to cut a straight slot of 10 mm width and 2mm depth by a cutter of 10 mm diameter between points (0,0) and (100,100) on the XY plane (dimensions in mm). The feed rate used for milling is 50 mm/min, milling time for the slot (in seconds) is
What is the correct answer?
4
A solid cylinder of diameter 100 mm and height 50 mm is forged between two frictionless flat dies to a height of 25mm. The percentage change in diameter is
What is the correct answer?
4
In _________ operation, the cutting force is maximum when the tooth begins its cut and reduces it to minimum when the tooth leaves the work.
What is the correct answer?
4
In grinding irregular, curved, tapered, convex and concave surfaces, the grinder used is
D. Tool and cutter grinder
What is the correct answer?
4
In metal cutting operations, the shear angle is the angle made by the shear plane with the
A. Direction of the tool axis
B. Direction of tool travel
C. Perpendicular to the direction of the tool axis
D. Central plane of the workpiece
What is the correct answer?
4
The cutting angle of a flat drill varies from
What is the correct answer?
4
Buffing wheels are made of
What is the correct answer?
4
The object of caulking in a riveted joint is to make the joint
What is the correct answer?
4
A type of welding flows, which is the result of a perfect proportion and mixture of acetylene and oxygen and is used for fusion welding of steel and cast iron, is
What is the correct answer?
4
The factor responsible for the formation of discontinuous chips is
A. Low cutting speed and large rake angle
B. Low cutting speed and small rake angle
C. High cutting speed and large rake angle
D. High cutting speed and small rake angle
What is the correct answer?
4
Carbide tipped tools usually have
What is the correct answer?
4
A 15 mm drilling machine means that it can drill a hole
A. Of maximum diameter 15 mm
C. Having cross-sectional area of 15 mm²
What is the correct answer?
4
A dense structure of a grinding wheel is used for