Related Questions
What is the correct answer?
4
A material in which the atoms are arranged regularly in some directions but not in others, is termed as 'mesomorphous material'; an example of which is
What is the correct answer?
4
Aluminium is extracted from
What is the correct answer?
4
Which of the following properties of a solid is not dependent on crystal imperfection?
What is the correct answer?
4
Pick out the wrong statement.
A. Molecules with symmetrical arrangements (e.g. CH4 or CCl4) are non-polar
B. Generally, non-polar compounds are chemically inactive, conduct electricity poorly and do not ionise
C. Most of the hydrocarbons are non-polar
What is the correct answer?
4
All of the following alloying elements of steel increases hardness but sacrifice ductility, except
What is the correct answer?
4
Air/fuel ratio on molar (volume) basis for combustion of methane with theoretical quantity of air with be
What is the correct answer?
4
Stresses encountered in the metal forming processes are less than the __________ of the material.
D. Limit of proportionality
What is the correct answer?
4
Minimum safe distance between two liquid fuel storage tanks is equal to (where, H = height of the tank)
What is the correct answer?
4
Faraday's law of electrolysis is related to the
B. Atomic number of the cation
C. Equivalent mass of the electrolyte
What is the correct answer?
4
Which of the following does not discharge the dust collected as a dry solid?
A. Electrostatic precipitator
D. Gravity settling chamber
What is the correct answer?
4
The most suitable material for die casting is
What is the correct answer?
4
Babbitt lining is used on brass/bronze bearings to increase the
A. Antifriction properties
What is the correct answer?
4
In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C.
What is the correct answer?
4
Galvanic corrosion cannot be prevented by
C. Usage of largest possible anodic area
What is the correct answer?
4
The delivery pressure of boiler feed water pump compared to the boiler steam pressure is
What is the correct answer?
4
A dense structure of grinding wheel is not used for the
What is the correct answer?
4
For efficient performance of a blast furnace, the extent of reduction of Wustite (FeO) should be
A. 100% indirect reduction
C. 50-60% indirect reduction
D. 30-40% indirect reduction
What is the correct answer?
4
Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.
What is the correct answer?
4
__________ stress cannot be sustained by a fluid in equilibrium.
What is the correct answer?
4
Maximum amount of thermal radiation is emitted at all wavelengths at any specified temperature by a/an __________ body.
What is the correct answer?
4
Chlorine acts as a bleaching agent only in the presence of
What is the correct answer?
4
Water hammer is caused in steam carrying pipelines, because of
A. Partial condensation of steam
B. Vibration of the pipeline
C. High degree of superheat of steam
D. Its exposure to torrential rain
What is the correct answer?
4
A jet engine turbine blade is normally manufactured by
What is the correct answer?
4
Pressure required to increase the density of water by about 1% is __________ atmosphere.
What is the correct answer?
4
The material used for coating the welding electrode is termed as the
What is the correct answer?
4
Which of the following is an acidic constituent of B.F. slag?
A.
What is the correct answer?
4
An atom bomb works on the principle of
C. Both the nuclear fission & fusion
What is the correct answer?
4
Propulsion of rocket follows from the
A. Newton's second law of motion
B. Newton's third law of motion
What is the correct answer?
4
The difference in one unit of Rockwell hardness number corresponds to a difference in the depth of indentation of __________ mm.
What is the correct answer?
4
Yield strength of a polycrystalline metal with an average grain size d, is proportional to