Home

What is the correct answer?

4

Wrought iron is never shaped by

A. Casting

B. Cold working

C. Forging

D. Welding

Correct Answer :

A. Casting


Related Questions

What is the correct answer?

4

__________ is not a case hardening process.

A. Carburising

B. Nitriding

C. Cyaniding

D. Annealing

What is the correct answer?

4

The bank of tubes located at the back of the domestic refrigerators are the __________ tubes.

A. Refrigerant cooling

B. Evaporator

C. Condenser

D. Throttling

What is the correct answer?

4

__________ of austenite decreases the hardenability in steel.

A. Fine grains

B. Coarse grains

C. Homogeneity

D. Dissolved elements (except cobalt)

What is the correct answer?

4

Which of the following is not an ore of copper?

A. Cryolite

B. Azurite

C. Chalcopyrite

D. Malachite

What is the correct answer?

4

Alloys having more than 80% copper are generally more

A. Abrasion resistant

B. Corrosion resistant

C. Prone to season cracking

D. Machinable

What is the correct answer?

4

In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the

A. Range is 15°F

B. Approach is 10°F

C. Both (A) & (B)

D. Neither (A) nor (B)

What is the correct answer?

4

A material being tested for endurance strength is subjected to the __________ load.

A. Impact

B. Completely reversed

C. Dynamic

D. Static & dynamic

What is the correct answer?

4

Lead is poured into the joint between two __________ pipes.

A. Mild steel

B. Concrete

C. Cast iron

D. Asbestos cement

What is the correct answer?

4

The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as

A. Rigid

B. Tough

C. Ductile

D. Plastic

What is the correct answer?

4

Gas turbine normally employs a constant __________ cycle.

A. Pressure

B. Temperature

C. Volume

D. None of these

What is the correct answer?

4

For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by

A.

B.

C.

D.

What is the correct answer?

4

A solar cell converts the sunlight directly into __________ energy.

A. Thermal

B. Electrical

C. Mechanical

D. Chemical

What is the correct answer?

4

Brazing filler metal used for joining steel plates

A. Melts below the melting points of base metals

B. Melts below 300°C

C. Is copper phosphorous alloy

D. Is copper

What is the correct answer?

4

Induced draft fans provided in large thermal power plant boilers have __________ blades.

A. Forward curved

B. Backward curved

C. Double curved

D. Radial or straight

What is the correct answer?

4

Heating of ferromagnetic materials to a temperature above Curie temperature makes it

A. Insulator for heat & electricity transmission

B. Ferritic

C. Behave like paramagnetic materials

D. Superconductor

What is the correct answer?

4

Tip of the match stick contains a mixture of

A. K + S

B. K + S + K2Cr2O7

C. S + K2Cr2O7 + White P

D. None of these

What is the correct answer?

4

Which of the following is normally not found in both the S.I. (petrol) & C.I. (diesel) engines?

A. Air filter

B. Fuel injector

C. Exhaust silencer

D. Battery

What is the correct answer?

4

Triple point of water is

A. 0°F

B. 492°R

C. 0°K

D. -273°C

What is the correct answer?

4

Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.

A. 5-10

B. 1000-1500

C. 120-500

D. 1500-3000

What is the correct answer?

4

Diffusion co-efficient of a metal in a solid solution depends upon its

A. Composition

B. Temperature

C. Both (A) & (B)

D. Neither (A) nor (B)

What is the correct answer?

4

What is the pH of distilled water?

A. 0

B. 1

C. 7

D. 14

What is the correct answer?

4

Referring to the periodic table of elements, it is found that with increasing atomic number. The atomic size in the same

A. Period increases

B. Period decreases

C. Group increases

D. Both 'b' & 'c'

What is the correct answer?

4

The difference between gross & net calorific values of fuel is due to the

A. Sensible heat carried away by the flue gases

B. Heat carried away by the steam from the moisture content of the fuel

C. Heat lost by radiation

D. Heat carried away by steam from the combustion of hydrogen in the fuel

What is the correct answer?

4

__________ stress cannot be sustained by a fluid in equilibrium.

A. Shear

B. Tensile

C. Compressive

D. None of these

What is the correct answer?

4

In the Bayer's process, bauxite is digested under pressure using

A. H2SO4

B. NaOH

C. NH3

D. HCl

What is the correct answer?

4

At the point of boundary layer separation in fluid flow, the

A. Shear stress is maximum

B. Velocity gradient is flat

C. Density variation is maximum

D. Shear stress is zero

What is the correct answer?

4

Identify the correct statement.

A. Sphlerite is zinc oxide

B. The first law of the thermodynamics is stated as δE = δQ - δW

C. Lead can be produced in a blast furnace

D. T. ferrooxidans is a fungus that can be used for leaching chalcopyrite

What is the correct answer?

4

Blow off cock is provided in steam boiler to

A. Guard the boiler in case of abnormal rise in steam pressure

B. Drain out water and sludge during its repair

C. Regulate the supply of water in boiler

D. Put out the fire in the furnace when the water level in the boiler falls to unsafe limit

What is the correct answer?

4

The activity of pure hydrogen gas at 1000°C and 5 atm pressure

A. Is always less than 1

B. Is always greater than 1

C. Can be 5

D. Depends on the choice of the standard state

What is the correct answer?

4

Pick out the wrong statement.

A. Cold cracking of a weld is due to the presence of hydrogen gas in the weld

B. True stress is given by, σ = σE (1 + εE), where σE and εE are engineering stress and engineering strain respectively

C. Phosphorous can be easily recovered in the iron blast furnace

D. High residual stress at the surface is beneficial for fatigue properties of a material