Related Questions
What is the correct answer?
4
The elastic strain in copper is due to the
A. Motion of dislocations
B. Stretching of atomic bonds
C. Breakage of atomic bonds
What is the correct answer?
4
As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint.
What is the correct answer?
4
__________ test can be termed as the semidestructive test.
What is the correct answer?
4
Gratings is associated with the measurement of
What is the correct answer?
4
Thermal conductivity of a material does not depend upon its
What is the correct answer?
4
Parallel straight line pattern of temperature distribution for both hot and cold fluids is observed in case of heat exchanger of the type
A. Parallel flow with equal heat capacities
B. Counter flow with equal heat capacities
C. Counter flow with unequal heat capacities
D. Parallel flow with unequal heat capacities
What is the correct answer?
4
To counteract the bad effects of strain hardening on a cold formed part, it must be
What is the correct answer?
4
Auto collimator is used to check
What is the correct answer?
4
Which of the following contributes maximum as main source of sulphur in the blast furnace charge?
What is the correct answer?
4
The atmospheric temperature during melting of ice/snow (in the atmosphere)
D. May increase or decrease; depends on the altitude where snow melts
What is the correct answer?
4
With increase in temperature, the electrical conductivity of semiconductors
D. Either (A) or (B), depends on the type of semi-conductor
What is the correct answer?
4
The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
What is the correct answer?
4
A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre.
What is the correct answer?
4
Heat transfer by __________ is almost absent in case of fluidised bed drying operation.
What is the correct answer?
4
Fire refining process is employed in case of
What is the correct answer?
4
Maximum consumption of limestone is in the __________ industry.
What is the correct answer?
4
Hot & cold working of material causes its __________ deformation.
What is the correct answer?
4
Velocity of a gas in sound is not proportional to (where, T = Absolute temperature of the gas. P = Absolute pressure of the gas. y = Ratio of specific heats (Cp/Cv) ρ = specific weight of the gas)
What is the correct answer?
4
Production of one ton of paper in Indian paper industry consumes about __________ kWh of electricity.
What is the correct answer?
4
Which of the following metals reacts violently with water?
What is the correct answer?
4
A high pressure boiler generates steam at a pressure greater than __________ kg/cm2.
What is the correct answer?
4
In an eutectic system, two elements are completely
A. Soluble in solid state
B. Insoluble in liquid state
C. Insoluble in both solid & liquid state
D. Soluble in liquid state
What is the correct answer?
4
__________ is the trade name assigned to a nonferrous cast alloy composed of cobalt, chromium & tungsten.
What is the correct answer?
4
In Newton's law of viscosity, which states that the shear stress is proportional to the __________ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, = velocity gradient).
What is the correct answer?
4
Which of the following phenomenon will exhibit the minimum heat transfer?
B. Forced convection in air
C. Free convection in air
What is the correct answer?
4
Spheroidising of a material is a/an __________ process.
What is the correct answer?
4
Carbon supply in pack carburising process is in the form of
What is the correct answer?
4
__________ of hard alloy and tool steel is done to make it easily machinable.
What is the correct answer?
4
The most important consideration in value engineering is the
What is the correct answer?
4
Yield strength of a material is determined by the __________ test.