Related Questions
What is the correct answer?
4
The friction factor for the turbulent fluid flow in a rough pipe does not depend upon the
A. Pipe roughness & pipe diameter
What is the correct answer?
4
In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C.
What is the correct answer?
4
Theoretical volume of oxygen required for complete combustion of 1Nm3 of acetylene, in oxyacetylene welding is __________ Nm3.
What is the correct answer?
4
__________ circuit is most commonly used to measure strain with the help of a strain gauge.
B. Voltage balancing potentiometric
C. Simple current sensitive
What is the correct answer?
4
Which of the following is not categorised as the ore agglomeration process?
What is the correct answer?
4
Transformation range for ferrous material is the temperature interval during which __________ is formed during its heating.
What is the correct answer?
4
Parallel straight line pattern of temperature distribution for both hot and cold fluids is observed in case of heat exchanger of the type
A. Parallel flow with equal heat capacities
B. Counter flow with equal heat capacities
C. Counter flow with unequal heat capacities
D. Parallel flow with unequal heat capacities
What is the correct answer?
4
Broaching tools are usually made of
What is the correct answer?
4
Lead is poured into the joints between two __________ pipes.
What is the correct answer?
4
The condition of diffraction from a crystal is given by
What is the correct answer?
4
__________ temperature remains constant during adiabatic saturation process of unsaturated air.
What is the correct answer?
4
Good design of the casing of a centrifugal pump aims at minimising the
What is the correct answer?
4
In the Bayer's process, bauxite is digested under pressure using
What is the correct answer?
4
__________ is the hardest material out of the following.
What is the correct answer?
4
Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that
A. Pure oxygen has been used for combustion
B. Nitrogen percentage in the fuel is very high
C. Excess air has been used for combustion
D. Hydrogen is not present in the fuel
What is the correct answer?
4
Brittleness induced due to the presence of sulphur in steel can be reduced by adding
What is the correct answer?
4
All the atoms of the world comprise of electrons, proton & neutron except that of __________ atom in which neutron is absent.
What is the correct answer?
4
The fugacity of liquid water at 298 K is approximately 3171 Pa. Considering the ideal heat of vaporisation as 43723 J/gm.mole, its fugacity at 300 K would be
What is the correct answer?
4
Friction factor for fluid flow in pipe does not depend upon the
C. Fluid density & viscosity
D. Mass flow rate of fluid
What is the correct answer?
4
Heat release during phase change is observed in case of a/an
What is the correct answer?
4
Adhesives
A. Cant be used in the form of pressure sensitive tapes
B. Cant join two dissimilar metals
C. Cure instantaneously after application on a surface
What is the correct answer?
4
The critical pressure at which the latent heat of vaporisation of steam becomes zero is __________ Kg/cm2.
What is the correct answer?
4
__________ property of steel increases by addition of large amount of silicon in it.
What is the correct answer?
4
A metal having a Poisson's ratio = 0.3 is elastically deformed under uniaxial tension. If the longitudinal strain = 0.8, then the magnitude of thickness strain is
What is the correct answer?
4
Minimum number of members required to form a Public Limited Joint Stock Com-pany is
What is the correct answer?
4
In __________ process, there is an increase in entropy with no degradation of energy.
B. Isochoric heat addition
D. Isobaric heat addition
What is the correct answer?
4
Pick out the wrong statement.
A. For a pressure vessel to be classified as 'thin vessel', the ratio of wall thickness to mean radius is less than 0.1
B. For calculating forces and efficiency of riveted joint, either rivet diameter or rivet hole diameter is used in case of pressure vessel and in structural work
C. Longitudinal joint is normally made butt joint to maintain the circularity of the vessel
D. Maximum diameter of the opening provided in a pressure vessel, which does not require any compensation is 200 mm
What is the correct answer?
4
Basicity of the slag in Indian blast furnace is in the range of
What is the correct answer?
4
In the diving apparatus, helium is used along with oxygen, because it is
B. Not soluble in blood at high pressure
D. Completely miscible with oxygen
What is the correct answer?
4
Silicon percentage in acid resistant cast iron is about