Related Questions
What is the correct answer?
4
The joint for soldering is supported by binding wire made of
What is the correct answer?
4
Percentage of differential pressure lost in a Venturimeter with a tapering of 15° may be about
What is the correct answer?
4
__________ furnace is generally used in the non-ferrous foundries.
What is the correct answer?
4
Cold cracking in the heat affected zone of a high strength steel weld can take place because of the
C. Relatively high sulphur content in the base metal
D. Sufficient hydrogen present in the welding arc
What is the correct answer?
4
Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.
What is the correct answer?
4
Liquor poisoning generally occurs due to the presence of __________ in it.
What is the correct answer?
4
Hot extrusion of aluminium is done in the temperature range of __________ °C.
What is the correct answer?
4
The product of a commercial direct reduction process is
D. Iron saturated with carbon
What is the correct answer?
4
Damage to metal surface by mechanical action is called
What is the correct answer?
4
Pressure required to increase the density of water by about 1% is __________ atmosphere.
What is the correct answer?
4
LVDT used for displacement measurement is a/an __________ transducer.
What is the correct answer?
4
If Reynolds number is greater than 1, then the
A. Viscous force is larger than the inertia force
B. Inertia force is larger than the viscous force
C. Inertia force is larger than the surface tension force
D. Inertia force is larger than the gravitational force
What is the correct answer?
4
Silicon percentage in silicon steel used for electrical equipments is about
What is the correct answer?
4
The elastic strain energy of a unit length of an edge dislocation as compared to that of a screw dislocation is
What is the correct answer?
4
In an eutectic system, two elements are completely
A. Soluble in solid state
B. Insoluble in liquid state
C. Insoluble in both solid & liquid state
D. Soluble in liquid state
What is the correct answer?
4
Which of the following is an example of cathodic protection of metals against corrosion?
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
Pick out the wrong statement.
A. Ductile fracture of a stressed material, which exhibits a large plastic deformation is commonly caused by the formation and coalescence of voids in the necked region
B. Brittle fracture is caused by the propagation of pre-existing cracks in the material and involves minimum plastic deformation
C. Fatigue fracture of a material is always brittle in nature and takes place due to the existence of line imperfections
D. Brittle materials are generally tested in tension
What is the correct answer?
4
Use of flux during soldering is done to
A. Increase fluidity of solder by lowering its melting temperature
B. Prevent oxide formation
C. Wash away surplus solder
What is the correct answer?
4
Thermodynamic cycle involved in the working of a thermal power plant is the __________ cycle.
What is the correct answer?
4
__________ is a special constituent of chlorophyll without which photosynthesis is not possible.
What is the correct answer?
4
Which of the following does not have a sharp melting point?
What is the correct answer?
4
An oxidation process is accompanied with decrease in the
What is the correct answer?
4
Which of the following gases cause global warming?
What is the correct answer?
4
A jet engine turbine blade is normally manufactured by
What is the correct answer?
4
Consumable electrodes are used in the __________ welding.
What is the correct answer?
4
For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by
What is the correct answer?
4
Tesla metre per ampere (T. m/A) is the unit for the measurement of
A. Magnetic susceptibility
C. Permeability of free space
What is the correct answer?
4
The efficiency of a Carnot heat engine operating between absolute temperatures T1 and T2 (when, T1 > T2) is given by (T1 - T2)/T1. The co-efficient of performance (CO.P.) of a Carnot heat pump operating between T1 and T2 is given by
What is the correct answer?
4
Milk is fat dispersed in water. It is an example of