Related Questions
What is the correct answer?
4
Which of the following mainly decides the current to be employed is arc welding?
C. Voltage across the arc
What is the correct answer?
4
The burnout heat flux in the nucleate boiling regime is not a function of the
C. Temperature difference
What is the correct answer?
4
Cementite is in the lamellar form in the __________ phase of steel.
What is the correct answer?
4
Maximum amount of thermal radiation is emitted at all wavelengths at any specified temperature by a/an __________ body.
What is the correct answer?
4
During sensible cooling of air, its wet bulb temperature
A. Decreases but dew point remains constant
B. Increases but dew point remains constant
C. Increases & the dew point decreases
D. Decreases & the dew point increases
What is the correct answer?
4
Pick out the wrong statement.
A. Molecules with symmetrical arrangements (e.g. CH4 or CCl4) are non-polar
B. Generally, non-polar compounds are chemically inactive, conduct electricity poorly and do not ionise
C. Most of the hydrocarbons are non-polar
What is the correct answer?
4
__________ is the most important element, which controls the physical properties of steel.
What is the correct answer?
4
The Al2O3 content of cryolite in Hall- Heroult cell is maintained between __________ percent.
What is the correct answer?
4
Out of the following, the alloy which has equal percentage of constituents, is
What is the correct answer?
4
Temper brittleness of a material can be fairly detected by the __________ test.
What is the correct answer?
4
An alloy of Fe - 0.4 % C is
What is the correct answer?
4
In extrusion of metals, which of the following statement is true?
A. Speed of the extruded material is same as that of ram speed
B. Redundant work is a function of the die angle
C. Relative motion between the billet surface and the container wall is always present
D. Hollow ram is used for indirect extrusion
What is the correct answer?
4
The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be
What is the correct answer?
4
Which of the following heat treatment processes is usually applied to castings?
What is the correct answer?
4
A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to
What is the correct answer?
4
__________ of hard alloy and tool steel is done to make it easily machinable.
What is the correct answer?
4
Which of the following is not the commercial name of poly-methyl-methacrylate (PMMA)?
What is the correct answer?
4
Glass reacts with
What is the correct answer?
4
X-rays are
D. Of higher wavelength than visible light
What is the correct answer?
4
Cold working of a material results in increase in hardness, which is termed as the __________ hardening.
What is the correct answer?
4
Angular displacement can be measured suitably by a
B. Linear variable differential transducer (LVDT)
What is the correct answer?
4
Heating of ferromagnetic materials to a temperature above Curie temperature makes it
A. Insulator for heat & electricity transmission
C. Behave like paramagnetic materials
What is the correct answer?
4
The approximate height of a blast furnace having a useful volume of 2000 m3 is about __________ metres
What is the correct answer?
4
Transformation range for ferrous material is the temperature interval during which __________ is formed during its heating.
What is the correct answer?
4
Which of the following fastening devices has its both ends threaded?
What is the correct answer?
4
Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by
What is the correct answer?
4
Eutectic reaction for iron-carbon system occurs at a temperature of __________ °C.
What is the correct answer?
4
In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases.
What is the correct answer?
4
Maximum hardenability of steel depends upon its
D. Alloying elements content
What is the correct answer?
4
Damage to metal surface by mechanical action is called