Related Questions
What is the correct answer?
4
An example of unsteady non uniform flow is the flow of liquid under pressure through a
A. Tapering pipe at constant flow rate
B. Tapering pipe at either decreasing or increasing flow rate
C. Long pipeline of constant diameter
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
Neutrons are present in all atoms except that of
What is the correct answer?
4
The noble metals
A. Are exemplified by Na, K and Li
B. Do not resist corrosion very strongly
C. Are the lowermost in the electro-chemical series of metals
What is the correct answer?
4
Atomic __________ is a whole number for an element.
What is the correct answer?
4
Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails
C. Below the elastic limit
What is the correct answer?
4
'Flare tower' used in industry is meant for
A. Venting off (after burning) the excess inflammable/toxic gases at high pressure
B. Absorbing the pollutant gases from the furnace exhaust
C. Cooling of furnace exhaust gases
What is the correct answer?
4
Steel & cast iron pipes are produced by __________ casting.
What is the correct answer?
4
The material used for coating the welding electrode is termed as the
What is the correct answer?
4
Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans?
A. Emissivity of pipe surface
B. Diameter & length of the pipe
C. Temperature of hot pipe surface & that of air in the room
What is the correct answer?
4
__________ is used for tying the steel columns to concrete foundation.
What is the correct answer?
4
Which of the following forces does not act on a fluid at rest?
What is the correct answer?
4
__________ pipe is the most suitable for carrying sanitary drainage.
B. Reinforced cement concrete
What is the correct answer?
4
In a good rimming steel
A. Carbon and silicon should be low
B. Silicon should be low but carbon should be high
C. Both silicon & carbon should be high
D. Silicon should be high but carbon should be low
What is the correct answer?
4
The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
What is the correct answer?
4
A compact estimate about the amount of materials handling between various work stations is obtained from the
What is the correct answer?
4
The approximate height of a blast furnace having a useful volume of 2000 m3 is about __________ metres
What is the correct answer?
4
Out of the following, the joint produced by __________ has the lowest strength.
What is the correct answer?
4
Ultimate strength in tension as compared to that in shear for steel is
What is the correct answer?
4
Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)?
What is the correct answer?
4
Factor of safety in machine design is defined as the ratio of ultimate stress to __________ stress.
What is the correct answer?
4
High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ percent.
What is the correct answer?
4
Which of the following fastening devices has its both ends threaded?
What is the correct answer?
4
Super conduction in metals is observed at a temperature of __________ °K.
What is the correct answer?
4
Dephosphorization of molten pig iron is favoured by
A. Oxidising and basic slag
B. Reducing and basic slag
C. High activity co-efficient of phosphorous in metal
D. Oxidising and neutral slag
What is the correct answer?
4
Which of the following is a boiler accessory
i.e., not a boiler mounting?
What is the correct answer?
4
Limestone addition in the blast furnace is done to flux __________ present in the raw materials.
What is the correct answer?
4
Silicon percentage in the silicon steel used for electrical appliances/equipments is
What is the correct answer?
4
Cobalt - 60 is used as a source of __________ in medical therapy & industrial radiography.
What is the correct answer?
4
The most important consideration in value engineering is the