Lewis form factor for 14 ½° composite and full depth involute system is (where T = Number of teeth)
0.124 - (0.684/T)
0.154 - (0.912/T)
0.175 - (0.841/T)
None of these
Correct Answer :
A. 0.124 - (0.684/T)
Related Questions
Oil in journal bearing should be applied at the point where load is
Nil or lightest
Maximum
Average
Any one of the above
The ball bearings are, usually, made from
Low carbon steel
High carbon steel
Medium carbon steel
High speed steel
The velocity factor for ordinary cut gears operating at velocities upto 12.5 m/s is equal to
0.75/ (0.75 + √v)
3/ (3 + v)
4.5/ (4.5 + v)
6/ (6 + v)
In a belt drive, if the pulley diameter is doubled keeping the tension and belt width constant, then it will be necessary to
Increase the key length
Increase the key depth
Increase the key width
Decrease the key length
The permissible stress in the fillet weld is 100 N/mm². The fillet weld has equal leg lengths of 15 mm each. The allowable shearing load on the weldment per cm length of the weld is
7.5 kN
10.6 kN
15 kN
22.5 kN
Basic hole is one
Whose upper deviation is zero
Whose lower deviation is zero
Whose lower as well as upper deviations are zero
Does not exist
Stress concentration in cyclic loading is more serious in
Ductile materials
Brittle materials
Equally serious in both cases
Depends on other factors
A key capable of tilting in a recess milled out in a shaft is known as
Woodruff key
Feather key
Flat saddle key
Hollow saddle key
A sliding bearing which can support steady loads without any relative motion between the journal and the bearing, is called
Hydrostatic lubricated bearing
Hydrodynamic lubricated bearing
Boundary lubricated bearing
Zero film bearing
The minimum number of teeth on the pinion which will mesh with any gear without interference for 20° full depth involute teeth will be
12
14
18
24
Applications in which stresses are encountered in one direction only uses following type of threads
Metric
Buttress
Acme
Square
Spring stiffness is
Ratio of coil diameter to wire diameter
Load required to produce unit deflection
Its capability of storing energy
Its ability to absorb shocks
Which of the following pipe joints would be suitable for pipes carrying steam?
Flanged
Threaded
Bell and spigot
Expansion
The smallest diameter of an external or internal screw thread is known as
Minor diameter
Major diameter
Pitch diameter
None of these
A bolt of uniform strength can be developed by
Keeping the core diameter of threads equal to the diameter of unthreaded portion of the bolt
Keeping the core diameter smaller than the diameter of the unthreaded portion
Keeping the nominal diameter of threads equal to the diameter of unthreaded portion of the bolt
None of the above
A coupling used to connect two perfectly aligned shafts, is
Muff coupling
Compression coupling
Flange coupling
All of these
In helical gears, the distance parallel to the axis, between similar faces of adjacent teeth, is called
Normal pitch
Axial pitch
Diametral pitch
Module
The wire ropes make contact at
Bottom of groove of the pulley
Sides and bottom of groove of the pulley
Anywhere in the groove of the pulley
Sides of groove of the pulley
In order to permit the thermal expansion/contraction of tubing, it should be
Crimped
Honed
Flared
Bent
In helical gears, the right hand helixes on one gear will mesh __________ helixes on the other gear.
Right hand
Left hand
Both A and B
None of these
Antifriction bearings are
Sleeve bearings
Hydrodynamic bearings
Thin lubricated bearings
None of the above
The size of a cam depends upon
Base circle
Pitch circle
Prime circle
Pitch curve
While designing a screw in a screw jack against buckling failure, the end conditions for the screw are taken as
Both the ends fixed
Both the ends hinged
One end fixed and the other end hinged
One end fixed and the other end free
A bolt of M 24 × 2 means that
The pitch of the thread is 24 mm and depth is 2 mm
Cross-sectional area of the threads is 24 mm²
The nominal diameter of bolt is 24 mm and pitch is 2 mm
The effective diameter of bolt is 24 mm and there are 2 threads per cm
The deflection of a cantilever beam under load W is 8. If its width is halved, then the deflection under load W will be
2/8
8/2
4/8
8/4
When the shaft rotates in anticlockwise direction at slow speed in a bearing, it will
Have contact at the bottom most of the bearing
Move towards right of the bearing making no metal to metal contact
Move towards right of the bearing making the metal to metal contact
Move towards left of the bearing making metal to metal contact
For same pulley diameters, center distance, belt speed and belt and pulley materials,
Open belt drive transmits more power than crossed belt drive
Crossed belt drive transmits more power than open belt drive
Open and crossed belt drives transmit same power
Power transmission does not depend upon open and crossed types of constructions
Form coefficient of spring is
Ratio of coil diameter to wire diameter
Load required to produce unit deflection
Its capability of storing energy
Concerned with strength of wire of spring
The function of a washer is to
Provide cushioning effect
Provide bearing area
Absorb shocks and vibrations
Provide smooth surface in place of rough surface
The load cup of a screw jack is made separate from the head of the spindle to
Prevent the rotation of load being lifted
Enhance the load carrying capacity of the jack
Reduce the effort needed for lifting the working load
Reduce the value of frictional torque