Related Questions
What is the correct answer?
4
Silicon in steel
A. Makes it usable in almost all magnetic circuits where alternating current is used
B. Increases its electrical resistivity and decreases the hysteresis loss
C. Is present upto 5% & 4% respectively when used in transformers & motor armatures
What is the correct answer?
4
Dislocations are __________ defects.
What is the correct answer?
4
Water-tube boiler is the one, in which
A. Water passes through tubes and flue gases around it
B. Tube carrying hot flue gases are immersed in a pool of water
C. Tubes are placed in vertical position
What is the correct answer?
4
An example of unsteady non uniform flow is the flow of liquid under pressure through a
A. Tapering pipe at constant flow rate
B. Tapering pipe at either decreasing or increasing flow rate
C. Long pipeline of constant diameter
What is the correct answer?
4
Super conduction in metals is observed at a temperature of __________ °K.
What is the correct answer?
4
The swift cup test evaluates the following property of a sheet metal.
What is the correct answer?
4
Most of the phosphorous present in the blast furnace burden enters into
What is the correct answer?
4
Moist climate is the most favourable factor in the site selection far a
What is the correct answer?
4
Constituents of stellite are
B. Cobalt, chromium & tungsten
C. Zinc, aluminium & nickel
D. Nickel, cobalt & vanadium
What is the correct answer?
4
Absolute zero pressure can be attained at a temperature of
What is the correct answer?
4
L.D. (Linz-Donawitz) converter is used in the production of
What is the correct answer?
4
In multipass welds, shot peening is done after each pass to
A. Close the surface porosity
B. Break the continuity of columnar grains
D. Introduce texture in the weld
What is the correct answer?
4
Brinell Hardness Number (BHN) for talc is approximately in the range of
What is the correct answer?
4
In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?
What is the correct answer?
4
Pearlite comprises of
A. 87% cementite & 13% Fe
B. 87% ferrite & 13% cementite
C. 93.33% ferrite & 6.67% C
What is the correct answer?
4
Work study deals with the __________ study.
What is the correct answer?
4
The critical pressure at which the latent heat of vaporisation of steam becomes zero is __________ Kg/cm2.
What is the correct answer?
4
Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode
A. Occurs higher in the electro-chemical series of metals
B. Is exemplified by magnesium plate
C. Is much cheaper than the cathodic base material to be guarded against corrosion
What is the correct answer?
4
Dryness fraction of dry steam is
What is the correct answer?
4
Copper deposits are found in India at the following location:
What is the correct answer?
4
Minimum number of members required to form a Public Limited Joint Stock Com-pany is
What is the correct answer?
4
Tempering of a material does not improve its
What is the correct answer?
4
Which of the following low melting alloy containing bismuth and lead is used for electric fuse?
What is the correct answer?
4
Large scale fire on fuel gas line is normally extinguished by
What is the correct answer?
4
Which of the following approaches the ideal gas behaviour most closely?
What is the correct answer?
4
Ganister contains maximum percentage of
What is the correct answer?
4
High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ percent.
What is the correct answer?
4
A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to
What is the correct answer?
4
Which of the following is not the commercial name of poly-methyl-methacrylate (PMMA)?
What is the correct answer?
4
The friction factor for the turbulent fluid flow in a rough pipe does not depend upon the
A. Pipe roughness & pipe diameter