Related Questions
What is the correct answer?
4
The maximum diameter of the hole that can be punched from a plate of maximum shear stress 1/4th of its maximum crushing stress of punch, is equal to (where t = Thickness of the plate)
What is the correct answer?
4
Which of the following statement is correct?
A. The stress is the pressure per unit area
B. The strain is expressed in mm
C. Hook's law holds good upto the breaking point
D. Stress is directly proportional to strain within elastic limit
What is the correct answer?
4
The value of shear stress which is induced in the shaft due to the applied couple varies
A. From maximum at the centre to zero at the circumference
B. From zero at the centre to maximum at the circumference
C. From maximum at the centre to minimum at the circumference
D. From minimum at the centre to maximum at the circumference
What is the correct answer?
4
In an isothermal process,
A. There is no change in temperature
B. There is no change in enthalpy
C. There is no change in internal energy
What is the correct answer?
4
If Th is the torque resisting capacity of a hollow shaft and Ts is that of a solid shaft, of the same material, length and weight. Then,
What is the correct answer?
4
When a gas is heated, change takes place in
What is the correct answer?
4
In an extensive property of a thermodynamic system
A. Extensive heat is transferred
B. Extensive work is done
C. Extensive energy is utilised
What is the correct answer?
4
Which of the following is a reversible non-flow process?
What is the correct answer?
4
The efficiency of the dual combustion cycle for the same compression ratio is __________ Diesel cycle.
What is the correct answer?
4
A circular shaft fixed at, A has diameter D for half of its length and diameter D/2 over the other half, as shown in the below figure. If the rotation of B relative to A is 0.1 radian, the rotation of C relative to B will be
What is the correct answer?
4
When a body is subjected to a direct tensile stress (σx) in one plane accompanied by a simple shear stress (τxy), the maximum shear stress is
A. (σx/2) + (1/2) × √(σx² + 4 τ²xy)
B. (σx/2) - (1/2) × √(σx² + 4 τ²xy)
C. (σx/2) + (1/2) × √(σx² - 4 τ²xy)
D. (1/2) × √(σx² + 4 τ²xy)
What is the correct answer?
4
When a body is subjected to a direct tensile stress (σx) in one plane accompanied by a simple shear stress (τxy), the maximum normal stress i
A. (σx/2) + (1/2) × √(σx² + 4 τ²xy)
B. (σx/2) - (1/2) × √(σx² + 4 τ²xy)
C. (σx/2) + (1/2) × √(σx² - 4 τ²xy)
D. (1/2) × √(σx² + 4 τ²xy)
What is the correct answer?
4
The fuel mostly used in steam boilers is
C. Coking bituminous coal
D. Non-coking bituminous coal
What is the correct answer?
4
Stirling and Ericsson cycles are
C. Semi-reversible cycles
D. Adiabatic irreversible cycles
What is the correct answer?
4
A cycle consisting of one constant pressure, one constant volume and two isentropic processes is known as
What is the correct answer?
4
An open cycle gas turbine works on
What is the correct answer?
4
Which of the following is a proper sequence?
A. Proportional limit, elastic limit, yielding, failure
B. Elastic limit, proportional limit, yielding, failure
C. Yielding, proportional limit, elastic limit, failure
What is the correct answer?
4
The unit of Young's modulus is
What is the correct answer?
4
For the same compression ratio, the efficiency of dual combustion cycle is
A. Greater than Diesel cycle and less than Otto cycle
B. Less than Diesel cycle and greater than Otto cycle
C. Greater than Diesel cycle
D. Less than Diesel cycle
What is the correct answer?
4
The principal constituents of a fuel are
What is the correct answer?
4
The smallest quantity of a substance, which can exist by itself in a chemically recognizable form is known as
What is the correct answer?
4
When it is indicated that a member is elastic, it means that when force is applied, it will
What is the correct answer?
4
Reversed joule cycle is called
What is the correct answer?
4
Which of the following process can be made reversible with the help of a regenerator?
A. Constant pressure process
B. Constant volume process
What is the correct answer?
4
The natural solid fuel is
What is the correct answer?
4
If Kh is the torque resisting capacity of a hollow shaft and Ks is that of a solid shaft, of the same material, length and weight. Then,
What is the correct answer?
4
The temperature at which the volume of a gas becomes zero is called
A. Absolute scale of temperature
B. Absolute zero temperature
What is the correct answer?
4
Which of the following is correct?
A. Absolute pressure = Gauge pressure + Atmospheric pressure
B. Gauge pressure = Absolute pressure + Atmospheric pressure
C. Atmospheric pressure = Absolute pressure + Gauge pressure
D. Absolute pressure = Gauge pressure - Atmospheric pressure
What is the correct answer?
4
The heat supplied to the gas at constant volume is (where m = Mass of gas, cv = Specific heat at constant volume, cp = Specific heat at constant pressure, T2 - T1 = Rise in temperature, and R = Gas constant)
What is the correct answer?
4
A process, in which the temperature of the working substance remains constant during its expansion or compression, is called