Related Questions
What is the correct answer?
4
The activity of pure hydrogen gas at 1000°C and 5 atm pressure
B. Is always greater than 1
D. Depends on the choice of the standard state
What is the correct answer?
4
The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be
What is the correct answer?
4
In case of condensers & evaporators operating under given terminal conditions, LMTD (logarithmic mean temperature difference) for counter flow as compared to that for parallel flow is
What is the correct answer?
4
The heat treatment to which the steel wire containing > 0.25% carbon is subjected to is
What is the correct answer?
4
Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses.
What is the correct answer?
4
For an ideal gas, Cp - Cv is
What is the correct answer?
4
Moist climate is the most favourable factor in the site selection far a
What is the correct answer?
4
Alloy powder manufactured by the following process have spherical shapes.
A. Electrochemical deposition
What is the correct answer?
4
The cathode in an electrochemical cell always carries
D. Positive or negative charge depending upon the nature of the cell
What is the correct answer?
4
The underground well of a biogas plant is called the
What is the correct answer?
4
Two solutions A1 & A2 have pH value of 2 & 6 respectively. It implies that the solution
A. A1 is more alkaline than solution A2
C. A2 is very slightly acidic
What is the correct answer?
4
Pick out the wrong statement.
A. Weldability of high carbon steel is poorer compared to low carbon steel
B. Invar is a magnetic alloy
C. Magnetic permeability of the diamagnetic material is less than one
D. Martenistic transformation never goes to completion (i.e., 100%) at room temperature
What is the correct answer?
4
Steel is welded using the __________ flame.
What is the correct answer?
4
When the wavelength of incident X-rays increases, the angle of diffraction
D. Shows no systematic variation
What is the correct answer?
4
__________ cannot increase the fatigue strength of a material.
What is the correct answer?
4
Tumbling is the process of improving the __________ of the materials/parts.
What is the correct answer?
4
Which of the following approaches the ideal gas behaviour most closely?
What is the correct answer?
4
Rain drops falling through atmospheric air attain limited terminal velocity, because of
A. Upward thrust due to air
B. Viscous force exerted by air
C. Surface tension effects of water
What is the correct answer?
4
Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling.
What is the correct answer?
4
Fatigue resistance of a material is measured by the
B. Ultimate tensile strength
What is the correct answer?
4
Working of linear variable differential transducer (LVDT) is based on the principle of variable
What is the correct answer?
4
In Newton's law of viscosity, which states that the shear stress is proportional to the __________ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, = velocity gradient).
What is the correct answer?
4
All the atoms of the world comprise of electrons, proton & neutron except that of __________ atom in which neutron is absent.
What is the correct answer?
4
For separating small pieces of metal from engine oil of a car, the best separating technique is the
D. Fractional distillation
What is the correct answer?
4
In practice, the compression ratio of compression-ignition (CI) engine ranges from
What is the correct answer?
4
Consideration of the creep is the most important in case of the
B. Piston of an I. C. engine
C. Flywheel of steam engine
What is the correct answer?
4
Induced draft fans provided in large thermal power plant boilers have __________ blades.
What is the correct answer?
4
Presence of nickel & chromium in steel does not raise its
What is the correct answer?
4
On being hit with a hammer, __________ will readily fracture.
What is the correct answer?
4
Which of the following is preferred for riveting?