Related Questions
What is the correct answer?
4
The burnout heat flux in the nucleate boiling regime is not a function of the
C. Temperature difference
What is the correct answer?
4
__________ is a special constituent of chlorophyll without which photosynthesis is not possible.
What is the correct answer?
4
What is the value of entropy at 273°K?
What is the correct answer?
4
The most serious manufacturing defect from fracture toughness point of view is
What is the correct answer?
4
Auto collimator is used to check
What is the correct answer?
4
Primary designation of steel is based on its
A. Hardness & tensile strength
D. Alloying elements content
What is the correct answer?
4
Presence of nickel & chromium in steel does not raise its
What is the correct answer?
4
In the diving apparatus, helium is used along with oxygen, because it is
B. Not soluble in blood at high pressure
D. Completely miscible with oxygen
What is the correct answer?
4
The minimum carbon content in steel should be __________ percent for it to respond to a hardening treatment.
What is the correct answer?
4
Addition of __________ to steel does not help in improving its machinability.
What is the correct answer?
4
Pick out the wrong statement about nucleate boiling.
A. Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface
B. Surface temperature is greater than the saturation temperature of the liquid
C. Heat transfer from the surface of the liquid is less than that in film boiling
D. The temperature is less than that of film boiling
What is the correct answer?
4
The main constituent of bones is
What is the correct answer?
4
Stainless steel is welded using
What is the correct answer?
4
Hydrogen can be
A. Used in I.C. engines as fuel
B. Liquefied & stored under cryogenic conditions
C. Produced by electrolysis of water
What is the correct answer?
4
Filler material used in welding should have __________ as compared to the parent metal to be welded.
A. Lower melting temperature
B. Same melting temperature
What is the correct answer?
4
Which of the following alloying elements is present in maximum percentage in high speed steel?
What is the correct answer?
4
__________ is the process of coating the surface of steel with aluminium oxide, thereby imparting it increased resistance to corrosion & oxidation upto a temperature of 700°C.
What is the correct answer?
4
Titanium is added to molten aluminium alloys before casting for the purpose of
B. Increasing corrosion resistance
What is the correct answer?
4
Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs?
What is the correct answer?
4
The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is
D. More but less than the diameter of bolt
What is the correct answer?
4
The behaviour of a metal specimen, which when plastically strained in tension reduces its yield stress in compression and vice versa; is termed as the
D. Stress recovery effect
What is the correct answer?
4
The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength.
What is the correct answer?
4
__________ stress cannot be sustained by a fluid in equilibrium.
What is the correct answer?
4
According to maximum shear stress failure criterion, yielding in material occurs, when the maximum shear stress is equal to __________ times the yield stress.
What is the correct answer?
4
For separating small pieces of metal from engine oil of a car, the best separating technique is the
D. Fractional distillation
What is the correct answer?
4
Biological shield in a nuclear reactor is generally provided to protect against the
What is the correct answer?
4
Metal shots used in shot blasting are made of
What is the correct answer?
4
An example of unsteady non uniform flow is the flow of liquid under pressure through a
A. Tapering pipe at constant flow rate
B. Tapering pipe at either decreasing or increasing flow rate
C. Long pipeline of constant diameter
What is the correct answer?
4
Limestone addition in the blast furnace is done to flux __________ present in the raw materials.
What is the correct answer?
4
Out of the following, the most malleable material is