Related Questions
What is the correct answer?
4
The product (s) of roasting of a sulphide ore is (are)
D. Dependent on temperature and partial pressure of oxygen & sulphur dioxide
What is the correct answer?
4
Which of the following is a boiler accessory
i.e., not a boiler mounting?
What is the correct answer?
4
In a drilling process, the metal is removed by both shearing & extrusion. General purpose drills are made of
What is the correct answer?
4
The units of the rate constant for a second order reaction are
What is the correct answer?
4
Liquor poisoning generally occurs due to the presence of __________ in it.
What is the correct answer?
4
Which of the following does not have a sharp melting point?
What is the correct answer?
4
Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30%?
What is the correct answer?
4
Pick out the wrong statement about the machinability of metals. Machinability of a metal
A. Decreases with increase in strain hardening tendencies
B. Decreases with increase in hardness, in general
C. Depend on the composition, microstructure and physical & mechanical properties
D. Decreases with increases in tensile strength & decrease in grain size
What is the correct answer?
4
The surface tension of a liquid, at critical temperature is
D. Same as that at any other temperature
What is the correct answer?
4
Which of the following forces does not act on a fluid at rest?
What is the correct answer?
4
Which of the following hardness tests does not measure the indentation hardness of metals and alloys?
B. Shore scleroscope test
D. Rockwell hardness test
What is the correct answer?
4
Pick out the wrong statement.
A. Ductile fracture of a stressed material, which exhibits a large plastic deformation is commonly caused by the formation and coalescence of voids in the necked region
B. Brittle fracture is caused by the propagation of pre-existing cracks in the material and involves minimum plastic deformation
C. Fatigue fracture of a material is always brittle in nature and takes place due to the existence of line imperfections
D. Brittle materials are generally tested in tension
What is the correct answer?
4
Addition of silicon to cast iron
A. Promotes graphite module formation
B. Improves its ductility
C. Does not promote graphite flakes formation
D. Increases the fluidity of molten metal
What is the correct answer?
4
Water-tube boiler is the one, in which
A. Water passes through tubes and flue gases around it
B. Tube carrying hot flue gases are immersed in a pool of water
C. Tubes are placed in vertical position
What is the correct answer?
4
Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation
A. Pressure falls below the vapour pressure
B. Pressure becomes very high
C. Temperature becomes low
What is the correct answer?
4
Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore?
A. High fusibility & fluidity
B. High thermal conductivity
D. High chemical activity
What is the correct answer?
4
Neutrons are present in all atoms except that of
What is the correct answer?
4
Matte smelting is used in the extraction of
What is the correct answer?
4
Tin based white metals are used, where bearings are subjected to
What is the correct answer?
4
A material in which the atoms are arranged regularly in some directions but not in others, is termed as 'mesomorphous material'; an example of which is
What is the correct answer?
4
Out of the following, the most malleable material is
What is the correct answer?
4
The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe)
What is the correct answer?
4
In case of a, centrifugal pump, the ratio h1/h2 is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller).
What is the correct answer?
4
Non-ferrous alloys used for making cutting tools need not have high
What is the correct answer?
4
Which of the following gases cause global warming?
What is the correct answer?
4
Stainless steel is welded using
What is the correct answer?
4
Wavelength of radiation emitted by a body depends on the __________ of its surface.
What is the correct answer?
4
The process of removal of scale formed during hot rolling of steel is termed as
What is the correct answer?
4
Nickel is a __________ material.
What is the correct answer?
4
The boiling & freezing points on a newly defined temperature scale in degree 'D' are 400°D & 100°D respectively. The temperature reading corresponding to 60°C on this new temperature scale will be equal to __________ °D.