Related Questions
What is the correct answer?
4
A compact estimate about the amount of materials handling between various work stations is obtained from the
What is the correct answer?
4
Minimum number of members required to form a Public Limited Joint Stock Com-pany is
What is the correct answer?
4
In a good rimming steel
A. Carbon and silicon should be low
B. Silicon should be low but carbon should be high
C. Both silicon & carbon should be high
D. Silicon should be high but carbon should be low
What is the correct answer?
4
Which of the following low melting alloy containing bismuth and lead is used for electric fuse?
What is the correct answer?
4
What is the pH of distilled water?
What is the correct answer?
4
Ganister contains maximum percentage of
What is the correct answer?
4
__________ is not used as the control rod material in a nuclear reactor.
What is the correct answer?
4
Which of the following is an example of stress corrosion?
A. Season cracking of brass
B. Caustic embrittlement of steel
What is the correct answer?
4
A jet engine turbine blade is normally manufactured by
What is the correct answer?
4
Insulation of liquid surface can be achieved by __________ on top of its surface.
A. Floating hollow polypropylene spheres
B. Spraying alumina powder
What is the correct answer?
4
The product out from a cupola is called
What is the correct answer?
4
A jig is used while __________ a hole.
What is the correct answer?
4
Materials having resistivity ranging from 1 to 100 ohm. cm is termed as
What is the correct answer?
4
Silicon percentage in acid resistant cast iron is about
What is the correct answer?
4
Large scale fire on fuel gas line is normally extinguished by
What is the correct answer?
4
The friction factor for the turbulent fluid flow in a rough pipe does not depend upon the
A. Pipe roughness & pipe diameter
What is the correct answer?
4
Which of the following has the least value of ultimate tensile strength (UTS)?
What is the correct answer?
4
Theoretical volume of oxygen required for complete combustion of 1Nm3 of acetylene, in oxyacetylene welding is __________ Nm3.
What is the correct answer?
4
Matte smelting is used in the extraction of
What is the correct answer?
4
Natural water contains approximately __________ percent of heavy water.
What is the correct answer?
4
Powder metallurgy technique is used in the production of __________ tools.
What is the correct answer?
4
Routing in production, planning & control is concerned with the
A. Sequence of operation to be performed
B. Progress of work performed
C. Authorisation of work to be performed
D. Balancing of load on machines
What is the correct answer?
4
Gage pressure within a spherical droplet of a fluid is 'p'. What will be gage pressure within a bubble of the same size & of the same fluid?
What is the correct answer?
4
In the X-ray radiography technique, the tube voltage for thicker plates as compared to thin plates, should be
A. Higher, as it gives higher wavelength
B. Lower, as it gives higher wavelength
C. Higher, as it gives shorter wavelength
D. Lower, as it gives shorter wavelength
What is the correct answer?
4
A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted will
D. May increase or decrease; depends on the thickness of each layer
What is the correct answer?
4
The activity co-efficient of the solute in a dilute solution
A. Decreases with the increase of concentration of the solute
B. Increases with the increase of concentration of the solute
D. Is unity at infinite dilution
What is the correct answer?
4
Load cells used for the measurement of weight has
A. Compact & rugged construction with an accuracy of 0.1 to 1%
B. No moving parts and incurs negligible deflection under load
C. Provision of thermal compensation and is hermetically sealed
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
The most abundant metal present in the earth's crust is;
What is the correct answer?
4
Dephosphorization of molten pig iron is favoured by
A. Oxidising and basic slag
B. Reducing and basic slag
C. High activity co-efficient of phosphorous in metal
D. Oxidising and neutral slag