Related Questions
What is the correct answer?
4
The lightest non-inflammable gas is
What is the correct answer?
4
Maraging steels derive their strength from the following mechanism:
A. A fine, highly dislocated and strong martensite
B. Fine dispersions of inter-metallic of Fe, Ni, Ti etc
C. Fine dispersions of alloy carbides in a ferrite matrix
D. Fine dispersions of C nucleated on dislocations in austenite
What is the correct answer?
4
Temperature attained in soldering of metals is about __________ °C.
What is the correct answer?
4
LVDT used for displacement measurement is a/an __________ transducer.
What is the correct answer?
4
Thermal equivalent of electrical power in practical calculation is __________ kcal/kWh.
What is the correct answer?
4
Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint.
What is the correct answer?
4
Which of the following materials has the poorest electrical conductivity?
What is the correct answer?
4
A 2 kg object weighs 1.8 kgf on a spring balance. The value of 'g' at that location in m/sec2 is
What is the correct answer?
4
The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler.
B. Evaporation efficiency
What is the correct answer?
4
The behaviour of a metal specimen, which when plastically strained in tension reduces its yield stress in compression and vice versa; is termed as the
D. Stress recovery effect
What is the correct answer?
4
Transformation range for ferrous material is the temperature interval during which __________ is formed during its heating.
What is the correct answer?
4
Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore?
A. High fusibility & fluidity
B. High thermal conductivity
D. High chemical activity
What is the correct answer?
4
As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint.
What is the correct answer?
4
Which of the following is used to produce draught in the locomotive boilers?
What is the correct answer?
4
Electrostatic separation of minerals from each other is based on their differences in the following property.
B. Magnetic permeabilities
C. Electrical conductivities
What is the correct answer?
4
The surface tension of a liquid, at critical temperature is
D. Same as that at any other temperature
What is the correct answer?
4
Addition of __________ to steel does not impart hardness.
What is the correct answer?
4
__________ is not a case hardening process.
What is the correct answer?
4
Electrical conductivities of semi-conductors are of the order of __________ ohm/cm.
What is the correct answer?
4
Pick out the wrong statement.
A. A soft magnetic material should have high permeability and small area of hysteresis loop
B. Poisson's ratio of high melting point metals is more than unity
C. Solders generally melt at less than 185°C
D. Steel produced by B.O.F process is ideally suited for manufacturing flat product
What is the correct answer?
4
Tesla metre per ampere (T. m/A) is the unit for the measurement of
A. Magnetic susceptibility
C. Permeability of free space
What is the correct answer?
4
Dry saturated steam can be converted into superheated steam by
A. Increasing its cross-sectional area of flow
B. Passing it through a pressure reducing valve
C. Forcing it downwards through a vertical tube
What is the correct answer?
4
Minimum safe distance between two liquid fuel storage tanks is equal to (where, H = height of the tank)
What is the correct answer?
4
Cold cracking in the heat affected zone of a high strength steel weld can take place because of the
C. Relatively high sulphur content in the base metal
D. Sufficient hydrogen present in the welding arc
What is the correct answer?
4
In a good rimming steel
A. Carbon and silicon should be low
B. Silicon should be low but carbon should be high
C. Both silicon & carbon should be high
D. Silicon should be high but carbon should be low
What is the correct answer?
4
Current employed in resistance welding ranges from __________ kVA/.
What is the correct answer?
4
Which of the following metals cannot be hot worked at room temperature?
What is the correct answer?
4
Magnetic permeability of iron is increased by its
D. Alternate heating & cooling
What is the correct answer?
4
Constituents of stellite are
B. Cobalt, chromium & tungsten
C. Zinc, aluminium & nickel
D. Nickel, cobalt & vanadium
What is the correct answer?
4
The maximum thickness of the metal which can be welded using ultrasonic welding is __________ mm.