Related Questions
What is the correct answer?
4
Stress concentration in static loading is more serious in
C. Equally serious in both cases
D. Depends on other factors
What is the correct answer?
4
Shear stress theory is applicable for
What is the correct answer?
4
If threads on a bolt are left hand, threads on nut will be
A. Right hand with same pitch
B. Left hand with same pitch
C. Could be left or right hand
D. Right hand with fine pitch
What is the correct answer?
4
In order to ensure self locking in a screw jack, it is essential that helix angle is __________ friction angle.
What is the correct answer?
4
The shock absorbing capacity of a bolt may be increased by
A. Increasing its shank diameter
B. Decreasing its shank diameter
C. Tightening the bolt properly
D. Making the shank diameter equal to core diameter of thread
What is the correct answer?
4
In a flange coupling, the bolts are subjected to
What is the correct answer?
4
The shock absorbing capacity of a bolt can be increased by
A. Tightening it properly
B. Increasing shank diameter
D. Making shank diameter equal to core diameter of thread.
What is the correct answer?
4
The static tooth load should be __________ the dynamic load.
What is the correct answer?
4
The width of the pulley should be __________ width of the belt.
What is the correct answer?
4
A shaft is subjected to a maximum bending stress of 80 N/mm² and maximum shearing stress equal to 30 N/mm² at a particular section. If the yield point in tension of the material is 280 N/mm² and the maximum shear stress theory of failure is used, then the factor of safety obtained will be
What is the correct answer?
4
The helix angle for single helical gears ranges from
What is the correct answer?
4
An imaginary circle which by pure rolling action gives the same motion as the actual gear, is called
What is the correct answer?
4
The pitch of threads on a Jock nut in comparison to pitch of nut is
What is the correct answer?
4
The sleeve or muff coupling is designed as a
What is the correct answer?
4
A type of brake commonly used in motor cars is a
D. Internal expanding brake
What is the correct answer?
4
Tensile strength of a mild steel specimen can be roughly predicted from following hardness test
What is the correct answer?
4
If T₁ and T₂ are the tensions on the tight and slack sides of the belt respectively, and Tc is the centrifugal tension, then initial tension in the belt is equal to
What is the correct answer?
4
Two shafts of the same length and material are joined in series. If the ratio of their diameters is 2, then the ratio of their angles of twist will be
What is the correct answer?
4
The value of Lewis form factor used in design of gears is
A. Dependent on number of teeth of a gear
B. Dependent on system of teeth
C. Independent of size of teeth
What is the correct answer?
4
When a circular beam of diameter d is subjected to a shear force F, the maximum shear stress induced will be
What is the correct answer?
4
A plate with an elliptical hole in the centre, with semi-major axis (A) perpendicular to the direction of loading and semi-minor axis (b) along the direction of loading, is subjected to a pull P. The maximum stress induced at the edge of the hole is equal to (where σ = Stress for a plate with no hole i.e. nominal stress)
What is the correct answer?
4
In the assembly of pulley, key and shaft
A. Pulley is made the weakest
B. Key is made the weakest
C. Key is made the strongest
D. All the three are designed for equal strength
What is the correct answer?
4
Buttress threads are usually found on
C. Spindles of bench vices
D. Railway carriage couplings
What is the correct answer?
4
The notch angle of the Izod impact test specimen is
What is the correct answer?
4
The maximum bending stress in a curved beam having symmetrical section always occur at the
What is the correct answer?
4
The design calculations for members subject to fluctuating loads with the same factor of safety, yield the most conservative estimates when using
What is the correct answer?
4
A thin spherical shell of internal diameter d is subjected to an internal pressure p. If V is the storage capacity of shell, then its diameter will be
What is the correct answer?
4
The velocity factor for precision metallic gears cut with high accuracy and operating at velocities upto 20 m/s is equal to
What is the correct answer?
4
According to maximum shear stress theory, the maximum shear stress in the shaft is
C. (1/2) × [σ + √(σ² + 4τ²)]
What is the correct answer?
4
In helical gears, the distance parallel to the axis, between similar faces of adjacent teeth, is called