Related Questions
What is the correct answer?
4
Optical activity is a/an __________ property.
What is the correct answer?
4
Which of the following hardness tests does not measure the indentation hardness of metals and alloys?
B. Shore scleroscope test
D. Rockwell hardness test
What is the correct answer?
4
Stellite is a __________ material.
D. Non-ferrous cast alloy cutting tool
What is the correct answer?
4
__________ test can be termed as the semidestructive test.
What is the correct answer?
4
Maximum permissible sulphur content in steel is __________ percent.
What is the correct answer?
4
Resistance of an electrical conductor is proportional to its (where, l = length and A = cross-sectional area of the conductor)
What is the correct answer?
4
Which of the following is an ore dressing operation?
What is the correct answer?
4
The life of a ball bearing is inversely proportional to
What is the correct answer?
4
Transformation range for ferrous material is the temperature interval during which __________ is formed during its heating.
What is the correct answer?
4
Window panes of aeroplanes are normally made of
C. Bakelite (phenol formaldehyde)
What is the correct answer?
4
Carbon supply in pack carburising process is in the form of
What is the correct answer?
4
Bad odour in sanitary latrines is reduced by periodically sprinkling
What is the correct answer?
4
Steel containing low percentage of nickel, chromium & tungsten are termed as the __________ steel.
What is the correct answer?
4
Carbon is present in the form of __________ in grey cast iron.
B. Nodular aggregates of graphite
What is the correct answer?
4
Uniform ramming of sand in green sand moulding process leads to
A. Reduced chance of gas porosity
B. Greater dimensional stability of the casting
C. Uniform flow of molten metal into the mould cavity
D. Less sand expansion type of casting defect
What is the correct answer?
4
The most serious manufacturing defect from fracture toughness point of view is
What is the correct answer?
4
For a spontaneous natural process at constant temperature and pressure, the free energy of the system always
D. Increases to a maximum before decreasing
What is the correct answer?
4
Mild steel has __________ crystal lattice structure.
A. Face centred cubic (fcc)
B. Body centred cubic (bcc)
What is the correct answer?
4
Wrought iron does not have
A. Uniform strength in all directions
B. Ability to hold protective coating
C. High ductility & corrosion resistance
D. Easily weldable characteristics
What is the correct answer?
4
Referring to the periodic table of elements, it is found that with increasing atomic number. The atomic size in the same
What is the correct answer?
4
Euler number is defined as the ratio of inertia force to __________ force.
What is the correct answer?
4
Compressed dry air is used as the cutting fluid, while machining
What is the correct answer?
4
The most abundant metal present in the earth's crust is;
What is the correct answer?
4
The cathode in an electrochemical cell always carries
D. Positive or negative charge depending upon the nature of the cell
What is the correct answer?
4
In chemical dehumidification of air
A. Both specific humidity & dry bulb temperature increases
B. Both specific humidity & dry bulb temperature decreases
C. Specific humidity decreases & dry bulb temperature increases
D. Specific humidity increases & dry bulb temperature decreases
What is the correct answer?
4
Electrical conductivities of semi-conductors are of the order of __________ ohm/cm.
What is the correct answer?
4
The cooling rate required to freeze 1 ton of water at 0°C into ice at 0°C in 24 hours is __________ BTU/hr.
What is the correct answer?
4
The two elements required to form substitutional solid solution should not have
A. Same crystalline structure
C. Widely differing electronegativity
What is the correct answer?
4
While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the
C. Better finish and surface appearance
D. High plastic deformation
What is the correct answer?
4
A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to