Related Questions
What is the correct answer?
4
An oxidation process is accompanied with decrease in the
What is the correct answer?
4
Normalising of a casting does not
B. Refine its grain structure
D. Improve its mechanical properties
What is the correct answer?
4
Yield strength of a material is determined by the __________ test.
What is the correct answer?
4
Which of the following is preferred for riveting?
What is the correct answer?
4
Good design of the casing of a centrifugal pump aims at minimising the
What is the correct answer?
4
Cold working of a material results in increase in hardness, which is termed as the __________ hardening.
What is the correct answer?
4
Internal energy of a gas obeying Van-Der- Waals equation of state, [p + (a/v2)] (V - b) = RT, depends upon its
A. Pressure & temperature
B. Pressure & specific volume
C. Temperature & specific volume
What is the correct answer?
4
The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times.
What is the correct answer?
4
__________ test can be termed as the semidestructive test.
What is the correct answer?
4
Thermal efficiency of an internal combustion engine is around __________ percent.
What is the correct answer?
4
Wave length of X-rays is about 1 angstrom; however it cannot pass through a sheet of
What is the correct answer?
4
Hydro-cyclone is a
What is the correct answer?
4
'Ice point' is designated on Fahrenheit temperature scale by
What is the correct answer?
4
A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient.
B. Inversely proportional to
C. Directly proportional to
What is the correct answer?
4
Compressed dry air is used as the cutting fluid, while machining
What is the correct answer?
4
Metal cutting by oxy-acetylene flame is accomplished by the __________ of the metal.
What is the correct answer?
4
For preparation of porous bearings by powder metallurgy, preferred particle shape is
What is the correct answer?
4
The effect of friction on the flow of steam through a nozzle is to decrease the __________ of steam.
What is the correct answer?
4
Which of the following is not the commercial name of poly-methyl-methacrylate (PMMA)?
What is the correct answer?
4
Specific gravity of a metal, which weighs 5 kg in air and 4 kg when submerged in water, will be
What is the correct answer?
4
A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted will
D. May increase or decrease; depends on the thickness of each layer
What is the correct answer?
4
Silicon crystal can be converted to p-type semiconductor by doping with
What is the correct answer?
4
A material in which the atoms are arranged regularly in some directions but not in others, is termed as 'mesomorphous material'; an example of which is
What is the correct answer?
4
Pick out the correct combination about the role of various additives used in polymers.
A. Plasticiser: increases the polymer strength
B. Heat stabiliser: increases the maximum service temperature
C. Fillers: Does not affect the property of polymer but increases its weight
D. Lubricants: increases the flexibility of polymers
What is the correct answer?
4
The swift cup test evaluates the following property of a sheet metal.
What is the correct answer?
4
Basicity of the slag in Indian blast furnace is in the range of
What is the correct answer?
4
Capacity & power requirement for an air compressor working at high altitude compared to sealevel will be
D. Either more or less; depends on the climatic conditions
What is the correct answer?
4
The surface tension of a liquid, at critical temperature is
D. Same as that at any other temperature
What is the correct answer?
4
Shampoos are commercially not available in the form of
What is the correct answer?
4
Which of the following is the most wear resistant grade of carbide used for the cutting tools?