Related Questions
What is the correct answer?
4
Vibration upto 100 kilo hertz can be most accurately measured by a __________ type accelerometer.
What is the correct answer?
4
When an isolated thermodynamic system executes a process,
B. Heat transfer takes place
C. Mass flow occurs across the boundary of the system
D. No chemical reaction takes place within the system
What is the correct answer?
4
In case of water (Prandtl number ≈ 6) flowing over a flat plate heated over the entire length, the thermal boundary layer thickness as compared to hydrodynamic boundary layer thickness is
What is the correct answer?
4
Tempering of a material does not improve its
What is the correct answer?
4
The elastic strain in copper is due to the
A. Motion of dislocations
B. Stretching of atomic bonds
C. Breakage of atomic bonds
What is the correct answer?
4
Steel & cast iron pipes are produced by __________ casting.
What is the correct answer?
4
Brass parts with high residual tensile stress at the surface are susceptible to season cracking (i.e. spontaneous cracking occuring on exposure to atmospheric corrosion), if its zinc percentage is more than
What is the correct answer?
4
With increase in temperature, the surface tension of water
What is the correct answer?
4
Water flow in the river during flood can be categorised as the __________ flow.
What is the correct answer?
4
Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.
What is the correct answer?
4
Specific gravity of hot metal (pig iron) is __________ times that of the blast furnace slag.
What is the correct answer?
4
Aluminium is extracted from
What is the correct answer?
4
Super conduction in metals is observed at a temperature of __________ °K.
What is the correct answer?
4
Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.
A. Induced draft fan
B. Economiser
C. Air preheater
D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories?
What is the correct answer?
4
The malleability of a material is the property by virtue of which it can be rolled or hammered into thin sheets. Which of the following materials has the maximum malleability?
What is the correct answer?
4
About __________ ton of coke is required in a cupola to produce one ton of casting.
What is the correct answer?
4
On being hit with a hammer, __________ will readily fracture.
What is the correct answer?
4
An oxidation process is accompanied with decrease in the
What is the correct answer?
4
In Newton's law of viscosity, which states that the shear stress is proportional to the __________ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, = velocity gradient).
What is the correct answer?
4
The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.
What is the correct answer?
4
Desalination of water
C. Means distillation of water
What is the correct answer?
4
Which of the following is prone to cup and cone fracture?
C. Round specimen of ductile metal
D. Flat tensile specimen of ductile metal
What is the correct answer?
4
Enzymes belong to the category of
What is the correct answer?
4
Which of the following is the most suitable abrasive for grinding high tensile strength materials?
What is the correct answer?
4
Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses.
What is the correct answer?
4
In the Bayer's process, bauxite is digested under pressure using
What is the correct answer?
4
Out of the following, maximum temperature drop for a given heat flow & for the same thickness will be in the case of
What is the correct answer?
4
__________ temperature remains constant during adiabatic saturation process of unsaturated air.
What is the correct answer?
4
The hardenability of steel decreases with
A. Decrease in dislocation density
B. Increase in solutionising temperature
D. Decrease in grain size
What is the correct answer?
4
Upto the critical radius of insulation, added insulation, will
A. Increase the heat loss
B. Decrease heat loss and will have no effect beyond that
D. Reduce convection heat loss compared to conduction heat less