Related Questions
What is the correct answer?
4
Theoretical volume of oxygen required for complete combustion of 1Nm3 of acetylene, in oxyacetylene welding is __________ Nm3.
What is the correct answer?
4
The cooling rate required to freeze 1 ton of water at 0°C into ice at 0°C in 24 hours is __________ BTU/hr.
What is the correct answer?
4
__________ property of a material is determined by the Herbert Pendulum device.
What is the correct answer?
4
Alloys having more than 80% copper are generally more
C. Prone to season cracking
What is the correct answer?
4
In the blast furnace, incorporation of water vapour in the blast gives the following effect.
A. Increases the reducing potential of the gas
B. Increases the flame temperature
C. No significant change occurs
D. Increases the hydrogen content in the metal
What is the correct answer?
4
At absolute zero temperature, for any reaction involving condensed phases
What is the correct answer?
4
Identify the correct statement with reference to the extractive metallurgy of aluminium.
A. The electrolyte consists of molten Na3AlF6 with approximately 1 to 8% Al2O3
B. Approximately 80% of the aluminium deposited on the cathode comes from cryolite
C. Sodium is deposited along with aluminium, but is immediately vaporised
D. Anode effect sets in when the cryolite concentration goes below 40%.
What is the correct answer?
4
For a thermodynamic system undergoing a process, which of the following pairs best expresses the relationship similar to that expressed by the pressure volume plot?
B. Temperature - pressure
What is the correct answer?
4
Thermal equivalent of electrical power in practical calculation is __________ kcal/kWh.
What is the correct answer?
4
Which of the following is the most wear resistant grade of carbide used for the cutting tools?
What is the correct answer?
4
Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation
A. Pressure falls below the vapour pressure
B. Pressure becomes very high
C. Temperature becomes low
What is the correct answer?
4
For preparation of porous bearings by powder metallurgy, preferred particle shape is
What is the correct answer?
4
The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint.
What is the correct answer?
4
Which of the following is the largest quantum of pressure?
What is the correct answer?
4
Induced draft fans provided in large thermal power plant boilers have __________ blades.
What is the correct answer?
4
Pipelines carrying various utilities in chemical industries are identified by their colour codes. The color of pipeline carrying steam is
What is the correct answer?
4
Hydrogen can be
A. Used in I.C. engines as fuel
B. Liquefied & stored under cryogenic conditions
C. Produced by electrolysis of water
What is the correct answer?
4
__________ joint is mostly used for joining pipes carrying water at low pressure.
What is the correct answer?
4
Diamagnetic materials
A. Are magnetised by eddy currents only
B. Are non-magnetic and cannot be magnetised
C. Are magnetised in direction opposite to the magnetic field
D. Can be magnetised in one direction only
What is the correct answer?
4
Pearlite comprises of
A. 87% cementite & 13% Fe
B. 87% ferrite & 13% cementite
C. 93.33% ferrite & 6.67% C
What is the correct answer?
4
Non-ferrous alloys used for making cutting tools need not have high
What is the correct answer?
4
When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively
What is the correct answer?
4
Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?
What is the correct answer?
4
Nickel and __________ are the alloying element added in steel to increase its toughness.
What is the correct answer?
4
Which of the following is an acidic constituent of B.F. slag?
A.
What is the correct answer?
4
__________ temperature remains constant during adiabatic saturation process of unsaturated air.
What is the correct answer?
4
__________ has a negative co-efficient of linear expansion.
What is the correct answer?
4
Matte smelting is used in the extraction of