Related Questions
What is the correct answer?
4
VLSM allows a network segment to have more than one subnet mask.
What is the correct answer?
4
Which of the following is a disadvantage of SANs?
What is the correct answer?
4
The _______ program goes out and finds the IOS and loads it.
What is the correct answer?
4
RIP has a hold-down period of ____________ seconds.
What is the correct answer?
4
A _________ provides a high-speed infrastructure to move data between storage devices and file servers.
What is the correct answer?
4
Which of the following is a private address?
What is the correct answer?
4
An OSPF's router ID is based on __________.
A. The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces
B. The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces
C. The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces
D. The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces
What is the correct answer?
4
You execute the line console 0 command from Configuration mode. What will the router's prompt be?
C. Router(config-interface)#
What is the correct answer?
4
A _________ connects two or more LANs in the same geographic area.
What is the correct answer?
4
Which interface type is used to connect to the serial interface of a router?
What is the correct answer?
4
The switch port that is chosen to forward traffic for a segment is called a __________.
What is the correct answer?
4
You have ISL trunks in your network and five VLANs configured. How many instances of STP are running?
What is the correct answer?
4
If you see a VC with an inactive status, this indicates ____________.
A. The connection between both Frame Relay DTEs is up and operational.
B. The connection between your Frame Relay DTE and DCE is up and operational, but there is something wrong with connection between your connected Frame Relay switch and the destination DTE.
C. You are not receiving any LMI messages from the Frame Relay switch.
What is the correct answer?
4
The ___________ converts an ISDN four-wire connection to a two-wire connection.
What is the correct answer?
4
Which IGRP command allows unequal-cost load balancing?
What is the correct answer?
4
Which router command would take you back to a suspended telnet session?
What is the correct answer?
4
You are given a Class B network with a subnet mask of 255.255.255.192. How many host
addresses are there on each subnet?
What is the correct answer?
4
What command activates the IP routing process?
What is the correct answer?
4
Which types of memory do not maintain their contents during a power-off state?
What is the correct answer?
4
The _________ is your network equipment, which includes the DCE (e.g., a modem) and the DTE (e.g., a router).
What is the correct answer?
4
Which router command would you use to test only layer-3 connectivity?
What is the correct answer?
4
Which prompt indicates that you are at User EXEC mode?
What is the correct answer?
4
Which of the following is a valid subnet mask value?
What is the correct answer?
4
Which protocol supports VLSM?
What is the correct answer?
4
Choose the following that a standard IP ACL can match on.
C. IP protocol information
What is the correct answer?
4
Which metric components, by default, are used in IGRP? (Choose all the correct answers.)
What is the correct answer?
4
The function of the MODE button is to __________.
A. Change the status of the ports
B. Affect what the SYSTEM and RPS LEDs represent
C. Affect what the port LEDs represent
D. Change the status of all the LEDs
What is the correct answer?
4
You are given a Class C network with 25 bits of networking. How many subnets do you have?
What is the correct answer?
4
The default encapsulation on a synchronous serial interface is _________.
What is the correct answer?
4
What uses 64 Kbps of bandwidth?