Which of the following pairs is not correctly matched?
Uranium - 233 : Fertile material
Binding energy : Mass defect
Scattering: Absorption cross-section
Number of nucleons : Mass number
Correct Answer :
A. Uranium - 233 : Fertile material
Related Questions
Use of water as a manometric liquid suffers from the disadvantage of its
Low vapour pressure
Corrosive nature
High vapour pressure
High boiling point
In the acid Bessemer process, the hot metal should have the following composition.
S < 0.05% and P < 0.05%
S < 0.05% and P < 1.5%
S < 0.05% and P > 1.5%
S > 1.5% and P < 0.05%
Which of the following metals is the most prone to work hardening?
Brass
Aluminium
Copper
Lead
Lead is poured into the joints between two __________ pipes.
Cast iron
Steel
Concrete
Plastic
The most suitable material for die casting is
Iron
Copper
Steel
Nickel
The friction factor for the turbulent fluid flow in a rough pipe does not depend upon the
Pipe roughness & pipe diameter
Fluid velocity
Type of flowing fluid
Both 'b' & 'c'
Thermit welding is categorised as the __________ welding.
Forge
Fusion
Resistance
Arc
The most abundant metal present in the earth's crust is;
Iron
Copper
Titanium
Aluminium
Viscoelastic behaviour is observed in __________ materials.
Non-crystalline organic polymeric
Ceramic
All crystalline
All amorphous
Air/fuel ratio on molar (volume) basis for combustion of methane with theoretical quantity of air with be
9.5 : 1
12.5 : 1
15.5 : 1
18.5 : 1
The phenomenon occurring during explosion of a hydrogen bomb is
Nuclear fission
Nuclear fusion
A combination of both nuclear fission & fusion
None of these
A psychrometer does not measure the __________ temperature of moist air.
Dew point
Dry bulb
Wet bulb
None of these
__________ glass is used in the mercury in glass thermometer meant for measuring a temperature of 500°C.
Borosilicate
High silica
Supermax
Lead
The passage between the nozzle and the __________ is called 'sprue' in case of injection moulding.
Runner
Cylinder
Mold
None of these
Hot & cold working of material causes its __________ deformation.
Visco-elastic
Isotropic
Elastic
Plastic
The normal stress is the same in all directions at a point in a fluid, only when the fluid
Is at rest & has zero viscosity
Is frictionless
Fluid layer has no motion relative to an adjacent layer of fluid
is incompressible & frictionless
__________ temperature remains constant during adiabatic saturation process of unsaturated air.
Dew point
Dry bulb
Wet bulb
None of these
Recrystallisation temperature of steel is __________ °C.
50
300
500
800
Which of the following has the least value of ultimate tensile strength (UTS)?
Medium carbon steel
High carbon steel
Cast iron
Wrought iron
Cast iron contains __________ percent carbon.
2.5
3.75
4.75
5.25
Which of the following is not a dielectric material?
Cotton, silk and paper
Asbestos, glass, porcelain and mica
Rubber and polymeric resins
All refractory materials
In a good rimming steel
Carbon and silicon should be low
Silicon should be low but carbon should be high
Both silicon & carbon should be high
Silicon should be high but carbon should be low
M10 index of coke indicates its
Compressive strength
Hardness
Abrasion resistance
Impact strength
Oxyacetylene reducing flame is used while carrying out welding on
Alloy steel
Grey cast iron
Mild steel
High carbon steel
__________ pipe is the most suitable for carrying sanitary drainage.
Stainless steel
Reinforced cement concrete
Cast iron
Asbestos cement
Metal shots used in shot blasting are made of
Stellite
Steel
Bronze
Lead
Highest cutting speed is achieved by the __________ tool material.
High speed steel
Carbide
Cast alloy
Plain carbon steel
Holes for riveting purposes should be preferably made by
Cutting torch
Drilling
Punching
None of these
Compressed dry air is used as the cutting fluid, while machining
Steel
Cast iron
Aluminium
None of these
__________ is not a case hardening process.
Carburising
Nitriding
Cyaniding
Annealing