Related Questions
What is the correct answer?
4
Which of the following are not features of ACLs?
A. Restricting telnet access to a router
B. Prioritizing WAN traffic
C. Filtering traffic from the router
D. Triggering dialup phone calls
What is the correct answer?
4
Which router-on-a-stick command defines the VLAN for the interface?
What is the correct answer?
4
Which command assigns a default gateway to the 2950 switch?
A. (config)# default-gateway
B. (config-if)# default-gateway
C. (config-if)# ip default-gateway
D. (config)# ip default-gateway
What is the correct answer?
4
RIP has a hold-down period of ____________ seconds.
What is the correct answer?
4
Which of the following is a Network layer protocol for the TCP/IP protocol stack?
What is the correct answer?
4
When you have configured PPP on an interface and use the show interfaces command, what state indicates the successful negotiation of a network layer protocol?
What is the correct answer?
4
Your router is running RIP and OSPF and both routing protocols are learning 192.168.1.0/24. Which routing protocol will your router use for this route?
What is the correct answer?
4
Which of the following is false concerning CHAP?
A. It sends an encrypted password.
C. It is more secure than PAP.
D. It uses a three-way handshake.
What is the correct answer?
4
RIP has a maximum hop count of ____________ hops.
What is the correct answer?
4
A ___________ is similar to a telephone circuit-switched connection.
What is the correct answer?
4
Which command defines interesting traffic?
What is the correct answer?
4
The function of the MODE button is to __________.
A. Change the status of the ports
B. Affect what the SYSTEM and RPS LEDs represent
C. Affect what the port LEDs represent
D. Change the status of all the LEDs
What is the correct answer?
4
With a crossover cable, which pins are crossed over?
What is the correct answer?
4
A _________ routes between different autonomous systems.
What is the correct answer?
4
Which prompt indicates that you are at User EXEC mode?
What is the correct answer?
4
Which type of traffic is not flooded?
What is the correct answer?
4
When using debug with PAP, which of the following message types might you see?
What is the correct answer?
4
You are in Interface Subconfiguration mode and want to completely return to Privilege EXEC mode. What would you enter? (Choose all correct answers.)
What is the correct answer?
4
An OSPF's router ID is based on __________.
A. The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces
B. The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces
C. The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces
D. The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces
What is the correct answer?
4
Which Frame Relay command is used to manually resolve addresses?
A. frame-relay interface-dlci
What is the correct answer?
4
If you wanted a list of parameters for the show command, you would type ________.
What is the correct answer?
4
If you see a VC with an inactive status, this indicates ____________.
A. The connection between both Frame Relay DTEs is up and operational.
B. The connection between your Frame Relay DTE and DCE is up and operational, but there is something wrong with connection between your connected Frame Relay switch and the destination DTE.
C. You are not receiving any LMI messages from the Frame Relay switch.
What is the correct answer?
4
_________ has a physical star topology but a logical ring topology.
What is the correct answer?
4
VLSM allows you to summarize __________ back to the class boundary.
What is the correct answer?
4
172.16.240.256 is a class __________ address.
What is the correct answer?
4
There are _________ actions a router can take when there is a match on an ACL statement
What is the correct answer?
4
Which of the following trunking methods is/are proprietary to Cisco?
What is the correct answer?
4
A _________ uses Gigabit Ethernet as a media type
What is the correct answer?
4
Which 1900 command enables port security?
D. switchport port-security
What is the correct answer?
4
RIP supports load balancing for up to __________ ___________ paths.